background image

PRODUCT SPECIFICATIONS

Automation Components, Inc.

2305 Pleasant View Road  |  Middleton, WI 53562

Phone:

 1-888-967-5224  |  

Website:

 workaci.com

Page 7

Version: 7.0

I0000598

WARRANTY

The AUD Series is covered by ACI’s Two (2) Year Limited Warranty, which is located in the front of ACI’S SENSORS & 
TRANSMITTERS CATALOG or can be found on ACI’s website: www.workaci.com.

24 VDC (24 VDC to 35 VDC) or 24 VAC (21.6 VAC to 28 VAC), 50/60 Hz.

208 mA maximum 

Relay contact closure, transistor, or triac (24 VAC, 50/60 Hz)

Normal Mode: 

5 to 26.4 VDC, 24 to 26.4 VAC  |  

Triac Mode:

 24 to 26.4 VAC

See page #3

0 to 1 VDC, 0 to 4 VDC, 0 to 10 VDC, 0 to 13 VDC, 1 to 2 VDC, 1 to 5 VDC, 1 to 11 VDC,  

1 to 14 VDC

0 to 20 VDC (with adjustable offset and span)

3300Ω minimum at 20 VDC ± 10% , 400 ohms minimum at 10 VDC ± 10% (If the 

voltage output is limited to 18 VDC on the high end of the output span, the DC supply 

limit can be 24 VDC –10% and maintain stated accuracy

0 to 16 mA, 4 to 20 mA

0 to 20 mA (with adjustable offset and span)

0 to 750Ω maximum (If the load is lowered to 700Ω, the DC supply can be 24 VDC –10% 

and maintain stated accuracy

Ab/- 2% of span for adjustable ranges, 5% for preset

Ab/- 3% of span for adjustable ranges, 5% for preset

256 steps (all ranges)

24 VDC (+/- 10%), 48 mA maximum

90° Pluggable Screw Terminal Blocks

16 (1.31 mm2) to 26 AWG (0.129 mm2)

0.5 Nm (Minimum); 0.6 Nm (Maximum)

35 to 120°F (1.7 to 48.9°C)

10 to 95% non-condensing 

-20 to 150°F (-28.9 to 65.5°C)

NON-SPECIFIC INFORMATION

 

Supply Voltage:
Supply Current: 
Input Signal Source:
Input Signal Trigger Level:
Input Full Range Rates of Change:
Output Voltage Fixed Signal 
Ranges:
Output Voltage Adjustable Signal 
Ranges:
Output Voltage Signal Load:

Output Current Fixed Signal Ranges:
Output Current Adjustable Signal 
Ranges:
Output Current Signal Load:

Output Signal Accuracy (24 VAC, 60 
Hz): 
Output Signal Accuracy (24 VAC, 50 
Hz):
Output Signal Resolution:
Regulated Power Output (User): 
Connections:
Wire Size:
Terminal Block Torque Rating:
Operating Temperature Range: 
Operating Humidity Range:
Storage Temperature:

Summary of Contents for INTERFACE AUD









Reviews: