BUTTON OPERATIONS
MODE BUTTON
Press the MODE button to move all functions in loop sequence from one function screen to another.
WHEEL CIRCUMFERENCE TABLE
1. The details below have been calculated using following formula: Tire Diameter (inches) x 25.4(mm/inches) x 3.1416 = wheel circumference (in mm).
2. The computer calculates the wheel rotating length between 2 signals; you have to set the wheel circumference in case your sensor is a reed sensor or an universal hall
sensor with magnet.
3. The setting value shall be changed be calculating the wheel circumference be divided by the ratio of wheel and speed cable gear, for example the wheel
circumference has to be divided 5 in case 1 wheel revolution equals 5 turns of speed cable.
4. You can use more magnets, but the setting wheel circumference must be divided by the number of magnet you installed.
5. Identify the tire size of your ATV/Motorcycle when you need to change different tire size and key in the corresponding number shown in the following chart.
Circumference
Tire Size
Tire Size
Circumference
Tire Size
Circumference
1436mm
18 inch
1357mm
17 inch
1277mm
16 inch
1197mm
15 inch
19 inch
1516mm
1756mm
1676mm
1596mm
22 inch
21 inch
20 inch
2075mm
1995mm
1915mm
1835mm
23 inch
26 inch
25 inch
24 inch
RESET BUTTON
1. Press MODE button to the desired screen then press RESET button for 2 seconds to reset TRIP
1, Trip 2, MAX, Max. temperature and MAX RPM data from stored values to zero individually.
2. The data of Trip 1, AVG & RT be reset at the same time when one of the 3 data functions is
being reset.
3. ODO, clock and TT data cannot be reset.
SHIFT RPM WARNING OPERATION
1. Press MODE button to the RPM screen; pull on the throttle until the desired shift RPM warning displayed.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer will flash to warning you shift gear.
4. Operate items 1 & 2 to readjust the shift warning RPM.
TEMPERATURE WARNING
1. The LCD screen will jump to temperature screen automatically when the sensor detects temperature higher than the presetting warning temperature.
2. The temperature digits flashes and both buttons are out of function during over temperature.
3. Stop engine until temperature cooling down to below presetting warning temperature, both bottons recover to work.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
RESET
2 sec
FUNCTIONS
BAR RPM: Bar Graphic Tachometer
The bar tachometer has 8,000rpm and 16,000rpm options.
RPM: Digital Tachometer
1. It displays up to 19,900 RPM.
2. Tachometer signal picked up from either CDI or Ignition coil.
Shift Warning RPM
1. The function enables you to set up an RPM shift warning.
2. Shift warning LED indicator lights green when RPM reaches 1000-500rpm,
and turns on amber when RPM reaches 500rpm in front of the setting value,
then flashes red when RPM reaches setting value, and stop flash after shift
gear.
MAX RPM: Maximum Tachometer
Displays highest tachometer reading achieved after last RESET operation.
SPD: Speed Meter
Displays speedometer reading up to 399.9 Km/H or 248.5 MPH.
MAX: Maximum Speed Meter
Displays highest speed achieved after last RESET operation.
AVG: Average Speed Meter
Calculates average speed from last RESET.
TRIP 1 & 2: Trip Meter 1& 2
TRIP function registers cumulative trip distance from last RESET while bike is
being ridden.
ODO: Odometer
1. ODO registers cumulative distance traveled during bike moving.
2. ODO data is adjustable when it is less than 30km, after that it stored in
memory and couldn't be reset.
RT: Riding Timer
1. Calculates total operation time from last RESET.
2. Count automatically begins with vehicle movement.
TT: Total Riding Timer
1. Calculates total operation time from the beginning of bike use.
2. TT data is stored in memory, even when power is off.
12/24 hour Clock
It displays 12- or 24-hour current time.
℃
/
℉
: Digital Thermometer
1. It displays -L-
℃
or -L-
℉
when temperature is lower than 50
℃ or 122℉ and displays -H-
℃
or -H-
℉
when temperature is over 180
℃ or 356℉.
2.
The LCD screen will automatic change to temperature screen and flashes the digits
of temperature when the thermo sensor detects temperature over the presetting
warning temperature; The MODE key is out of function until the temperature cooling
down and lower than the presetting waring temperature.
MAX
℃
/
℉
: Maximum Temperature Meter
Displays highest temperature achieved after last RESET operation.
Volt:
Digital Voltage Gauge
It checks bike's battery and charging system health,
: Bar Thermometer
1. It has 7 bars to indicat engine temperature and always displayed.
2.
The 4th bar counts from bottom be turned when temperature reaches the preset
warning temperature, each adding or decressing 15
℃
lights on/off a bar based on
the 4th bar.
:
Bar Fuel Meter
1. Have 7 bar to indicate how much fuel remains.
2. Built-in 100, 250, 500 Ohm and Off modes, the fuel bar will disappear if you
select off mode.
3. Last bar flashes to indicate low fuel level automatically.
