Acer X203H Service Manual Download Page 34 | Manualshive

Page: 34 / 70

background image

- 34 -

5. Level 1 Cosmetic / Appearance / Alignment Service

5.1 Alignment procedure (for function adjustment)

5.1.1 Preparation

1. Setup input timing to any preset modes or patterns.
2. Enter factory mode (press “Empowering” & “Power” buttons at the same time to turn on monitor).
3. Move cursor into “Burn-in Mode” tag and select “On” to enable burn-in mode.
4. Power off the monitor, remove the input source and then power on again.
5. Setup unit and keep it warm up for at least 30 minutes.
6. Setup input timing ICL-605( 1280x1024@75Hz ), 32-Grays pattern.
7. Setup unit and keep it warm up at least 30 minutes.

5.1.2. Timing adjustment:

1. Enter factory setting area (press “

Empowering

” and then press “SOFTPOWER”).

2. Check the settings to following values:

Contrast = 50
Brightness = 85
Color = Warm
Language = English

Then, turn off the monitor power.

3. Turn on power enter user area.

«
...
32
33
34
35
36
...
»

Summary of Contents for X203H







































































Reviews:

No comments

Related manuals for X203H

Brand: IBM Pages: 32

WV-CK2020A - 20" CRT Display

Brand: Panasonic Pages: 2

Brand: iHealth Pages: 2

LCD3215 - MultiSync - 32" LCD Flat Panel...

Brand: NEC Pages: 34

Cintiq Pro DTH-3220

Brand: Wacom Pages: 78

Brand: Lilliput Pages: 18

Brand: smartheart Pages: 82

Brand: e-Ink Pages: 18

Brand: Yada Pages: 16

Brand: Z Microsystems Pages: 32

Brand: Miro Displays Pages: 35

Brand: Mitsubishi Pages: 84

Brand: switel Pages: 44

Two -Way Intercom Monitor

Brand: Safety 1st Pages: 5

Brand: G-STORY Pages: 41

Brand: AOR Pages: 39

Brand: AOC Pages: 64

Brand: Pyle Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands