Acer X1170 series Page 32 User Manual Download

Page: 32 / 66

ish

Image

Projection

(for X1170/X111/X1170N/X1270N series only)

•

Front-Desktop: The factory default setting.

•

Rear-Desktop: When you select this function, the projector

reverses the image so you can project from behind a translucent

screen.

•

Rear-Ceiling: When you select this function, the projector reverses

and inverts the image at same time. You can project from behind

a translucent screen with ceiling mounted projection.

•

Front-Ceiling: When you select this function, the projector inverts

the image for ceiling-mounted projection.

Keystone

Adjust image distortion caused by tilting projection. (±40 degrees)(for

X1170/X111/X1170N/X1270N series only)

Projection mode

(for X1270/X1270Hn/X1170A series only)

•

Front: The factory default setting.

•

Rear: Reverses the image so you can project from behind a

translucent screen.

Projection Location (for X1270/X1270Hn/X1170A series only)

•

Auto: Automatically adjusts projection location of image.

•

Desktop

•

Ceiling: Turns the image upside down for ceiling-mounted

projection.

Auto Keystone

Automatically adjusts vertical image. (for X1270/X1270Hn/X1170A

series only)

Summary of Contents for X1170 series



































































Search results

Summary of Contents for X1170 series

Reviews:

Related manuals for X1170 series

Brands by name

Popular brands

Acer X1170 series, User Manual

Search results

Summary of Contents for X1170 series

Reviews:

Related manuals for X1170 series

Brands by name

Popular brands