Acer P7270I Refresh Service Manual Download Page 100

Page: 100 / 171

P7280/P7270I/P7280 Refresh/P7270I Refresh

Confidential

4-6

- Ref. below table

Note: The defect criteria follows TI specification.

4. Dead Pixel (Bright pixel)

Procedure

- Test equipment: video generator.

- Test signal: analog 1024x768@60Hz.

- Test Pattern: full black

Inspection item

- Bright pixel check.

Note: Frame dimension under operative zone1

inch

Criteria

- Bright pixel is unacceptable.

- Ref. below table

Note: The defect criteria follows TI specification.

5. Dead Pixel (Dark pixel)

Procedure

- Test equipment: video generator.

- Test signal: analog 1024x768@60Hz.

- Test Pattern: full white

Inspection item

- Dead pixels check.

- White pattern (IRE=100)

- Adjacent dark pixel.

Criteria

- The number of the dead pixels should be less or

equal to 6 pixels.

- Adjacent pixel with each other is unacceptable.

- Ref. below table

Note: The defect criteria follows TI specification.

6. Focus test

Procedure

- Test equipment: video generator.

- Test signal: analog 1024 x 768@60Hz

- Test Pattern: full screen or MEME Sony

Inspection item

- Focus check

Criteria

- From screen 1.91 M

via visual to check the focus, look at the entire

screen, focus shall be clear, crisp, and sharp
over the entire surface of the display
pattern.(Blur word on one of the corner after
adjustment is acceptable. However, the word

Full black

Full white

MEME Sony

Full screen

Summary of Contents for P7270I Refresh












































































































































































Search results

Summary of Contents for P7270I Refresh

Reviews:

Acer P7270I Refresh, Service Manual, Page: 100 / 171

Search results

Summary of Contents for P7270I Refresh

Reviews: