2-4
System Utilities
Entering CMOS setup
0
1.Turn on the server and the monitor.
If the server is already turned on, close all open applications, then restart the server.
2.During POST, press Delete.
If you fail to press Delete before POST is completed, you will need to restart the server.
The Setup Main menu will be displayed showing the Setup’s menu bar. Use the left and right
arrow keys to move between selections on the menu bar.
Navigating Through the Setup Utility
0
Use the following keys to move around the Setup utility.
→
←
: Select Screen
↑
↓
: Select Item
Enter: Select
+ / - / Space: Change Opt.
F7: Load User-defined Defaults
F8: Save as User-defined
F9: Optimized Defaults
F10: Save & Exit
Esc: Exit
NOTE:
NOTE
:
Grayed-out fields are not user-configurable.
Enter
key–Display a submenu screen.
NOTE:
NOTE
:
Availability of submenu screen is indicated by a(>).
Esc
–If you press this key:
On one of the primary menu screens, the Exit menu displays.
On a submenu screen, the previous screen displays.
When you are making selections from a pop-up menu, closes the pop-up without
making a selection.
F1
–Display the General Help panel.
F6
–Press to load optimized default system values.
F10
–Save changes made the Setup and close the utility.
Summary of Contents for Aspire ZS600
