background image

Turning on the system 

After making sure that you have properly set up the system, applied power and connected 

all the necessary peripherals, you can now power on the system. Follow the procedure 

below. 

 

Press the power button 

 

The system starts up and displays a welcome message on the monitor. After that, a series 

of power-on self-test (POST) messages appears. The POST messages indicate if the 

system is running well or not. 

 

 

Note: 

If the system does not turn on or boot after   

pressing the power button, go to the next section   

for the possible causes of the boot failure

 

 

Aside from the POST messages, you can determine if the system is in good condition by 

checking if the following occurred. 

 

The power status indicator on the front panel lights up blue. 

 

The Num Lock, Caps Lock and Scroll Lock indicators on the keyboard light up. 

 

Power-on problems 

If the system fails to boot after you have applied power, check the following factors that 

might have caused the boot failure. 

 

The external power cord may be loosely connected. 

 

Check the power cord connection from the power outlet to the power cord socket on 

the rear panel. Make sure that the cord is properly connected to the power outlet and to 

the power cord socket. 

No power comes from the grounded power outlet. Have an electrician check your 

power outlet. 

 

Loose or improperly connected internal power cables.

 

Check the internal cable connections. If you are not confident to perform this step, ask 

a qualified technician to assist you. 

 

Warning! Make sure all power cords are   

disconnected from the electrical outlet before   

performing this task.

 

 

 

Summary of Contents for Altos BrainSphere P10 F7 SFF









































Reviews: