manualshive.com logo in svg

ACEK9 Hot-N-Pop Pro, Installation Manual

Share
Download
ACEK9 Hot-N-Pop Pro Installation Manual Download Page 17

16

Step 22 Finish Install and Test System

Recheck wiring placement, and connections. Secure cables and wires with cable ties. Install
the IntelaBox in its accessible location. Protect all connections, components that may be

exposed to weather, when wires run through grommets check that the have been properly
sealed to keep water entry. Completely test the K9 Hop-N-Pop® Pro. Check the K9 Door

Popper® with the remote at a distance and from the control head. Confirm that the K9 Door
Popper® does not release the door when the vehicle is in gear. See test procedure.

IMPORTANT: It is the responsibility of the Installer and the Handler to confirm that

all safety features are installed and working properly at the time of installation.
The handler is also responsible to make continuing periodic checks of all safety

systems of this product.

K9 Door Popper Test Procedure

1) The default power settings are Door Popper and Heat Alarm is “ON/Off with Car”. When
the ignition is turned ON, the Heat Alarm and Door Popper will power up.

2) With door popper on. Observe the pop status light.
3) Put the vehicle in PARK and confirm that the Door Popper status light is ON; this indicates

that Door Popper is READY.
4) Put the vehicle in REVERSE and through ALL the DRIVE gears, D-3-2-1 etc. and confirm

that the Door Popper status light FLASHES, this indicates that Door Popper is DISABLED.
5) With the vehicle in gear press BOTH the UP and DOWN keys simultaneously -or- press and

hold any button on the remote and the door should NOT Pop.
6) Lock the doors from the drivers switch.

7) Put the Vehicle IN PARK, Press BOTH the UP and DOWN keys simultaneously –or- press
and hold any button on the remote and the door should pop. Note the other doors should

remain locked to prevent unwanted entry into vehicle.
8) Lock the doors and retest. Verify that the door that is locking and unlocking.

9) Test Door Popper Remote at a distance of 200 to 500 feet to confirm remote’s range.
10) Visually inspect that the gas spring is mounted at an angle (rod down) and confirm the
brackets are not binding and that the door fully opens.

11) Repeat Heat Alarm test (Step 13)

If any of these tests fail please check the installation.

Contact AceK9.Com Support with the Serial Number, Call 772-600-7574

Be sure K9 handler receives a copy of the User Manual.

Acek9.com Two (2) Year Limited Warranty

For details visit http://www.acek9.com

Summary of Contents for Hot-N-Pop Pro




















Reviews:

No comments

Brands by name

Popular brands

Load more brands