ACE COMPUTERS PWB411 Page 18 User Manual Download | Manualshive

Page: 18 / 23

background image

ACE097

Page 18 of 23

Rev Date:3.18.2022

Installing the PHM into the CPU Socket

1.

Remove the plastic protective cover from the CPU socket. Gently squeeze the grip tabs then pull
the cover off.

2.

Locate the threaded fasteners (a, b, c, d) on the CPU socket.

«
...
16
17
18
19
20
...
»

Summary of Contents for PWB411
























Reviews:

No comments

Related manuals for PWB411

Brand: NAIM Pages: 16

SUPERSERVER 6034H-X8R

Brand: Supermicro Pages: 128

Brand: Sun Microsystems Pages: 4

DIGITAL Server 9100 Series

Brand: Digital Equipment Pages: 68

Transport GT26-B4987

Brand: TYAN Pages: 125

FusionServer 2288 V5

Brand: xFusion Digital Technologies Pages: 86

Brand: Goonas Pages: 13

Brand: IBM Pages: 1730

Brand: D-Link Pages: 40

Brand: Lexmark Pages: 76

Brand: Lexmark Pages: 134

System x3300 M4

Brand: IBM Pages: 52

PowerEdge R6415

Brand: Dell EMC Pages: 139

Brand: Oce Pages: 464

Brand: USR IOT Pages: 48

Brand: Promise Technology Pages: 2

VANTAGE RADIUS 50

Brand: ZyXEL Communications Pages: 1

Brand: ZyXEL Communications Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands