Installation Guide
10
11
Cheetah iSharer-3010
Network Configuration
This Installation Guide is designed to help install the Cheetah iSharer-3010 on your
network. The instructions included in this section assume you are setting up a new
network.
There are five steps to set up the Cheetah iSharer-3010 as descibed below:
1. Hardware Installation
: Setting up the hardware connection, power, and other
devices.
2. Client Side Network Settings
: Configuring the client side
TCP/IP in order to access and configure the Cheetah iSharer-3010.
3. Cheetah iSharer-3010 Settings
: Configuring the Cheetah iSharer-3010 using a
Java compatible Web browser or Telnet program.
4. Testing
: Using a Web browser to access an external Internet site to verify that all
the settings are correct.
5. Setting up Other Clients
: Setting up all other client stations on the same LAN.
Hardware Installation
The following are instructions for setting up the Cheetah iSharer-3010. Refer to the
illustration, and follow the steps shown below to quickly install your Cheetah iSharer-
3010.
Figure 3.1 - Cheetah iSharer-3010 Hardware Installation
1. Connect one end of an RS-232 serial cable (not included in the package) to the
modem or ISDN TA, and the other end to the DB-9 serial port labeled “Modem1”
on the back of the Cheetah iSharer-3010.
2. Connect a dedicated phone line to a modem or ISDN TA.
3. Connect the power adapter to a modem or ISDN TA, and turn on the power. We
suggest connecting and configuring a single modem first. You can add a second
modem if needed, repeating the same procedure for setting up the first modem.
4. Use standard twisted-pair Ethernet cable to connect computers or any other
Ethernet devices to the RJ-45 ports of the Cheetah iSharer-3010.
5. Plug the CheetahiSharer-3010’s power supply into an AC power outlet, then plug
the power supply output cable into the power connector on the rear of the unit.
The Power LED should light up immediately.
Note:
The Cheetah iSharer-3010 includes an eight-port hub. Use straight-through
UTP cables to connect computers or other end stations to any RJ-45 port on
the rear panel. (Set Port 8 to “MDI-X” when connecting these kinds of
devices.) Port 8 can be adjusted to serve as an uplink port by setting the slide
switch to “MDI”. When set to this position, you can use straight-through UTP
cable to attach this port to a standard port (that uses an internal crossover)
on another hub or a switch.
Network Settings at Client Site
After installing the Cheetah iSharer-3010, please follow the procedures below to
configure it:
1. Choose a computer in the LAN to configure the Cheetah iSharer-3010. From
Windows 95, double click “My Computer.”
2. Double click “Control Panel.”
3. Double click “Network.” This window shows information about the network
interface card you installed. Verify that the “TCP/IP” component is installed. If
not, install it, otherwise, go to Step 6.
Summary of Contents for Cheetah iSharer-3010
