background image

10

2.8 Simple Trouble shooting

Problem

Possible reason

Solution

Top speed too slow

1. Low battery voltage

2. Handlebar control problem

3. Damage to motor drive-line

1. Recharge battery fully

2. Call service

3. Call service

Power on, but motor
not working

1. Battery not connected

2. Motor connection damaged

3.Handlebar control problem

1. Re install battery

2. Call service

3. Call service

Low range after
recharging the battery

1. tire pressures too low

2. Undercharge or charger fault
3. Battery capacity loss or
damage

4. Hill climbing, frequent stops, strong
headwinds, overloading.

1. Check pressures

2. Recharge completely or have
charger inspected

3. Replace battery

3 Controls and equipment

In this section, the functions and any specific maintenance needed on all the main controls and
ancillary equipment are described.

3.1 Battery on/off switch and lock

3.1.1 Your Accolmile bike is supplied with two identical keys. The key locks the battery to the bike.

3.1.2 The battery is connected to the electrical system of the bike automatically when you slide

the battery into the frame. To turn on the bike’s electrical system, Press down the button

directly above the frame to turn on the power, press the button again to turn off the power.

Summary of Contents for 700C






































Reviews: