background image

11

www.acclaimlighting.com

9

6

3

8

5

2

10

7

4

1

256

128

64

32

16

DMX mode: ON

8

DMX address

4

2

1

ON

AQUA DRIVER 150 MODE CONTROL

The manner in which the four output ports are grouped and operate is determined by the 
settings of the two switch blocks located on the front panel 

(Note: all switch settings can be 

changed when the driver is off or on)

. There are three main ways to use the Aqua Driver 150:

 

External DMX control mode

 

Standalone mode using internal chase programs

 

Standalone mode using adjustable static dimming

EXTERNAL DMX CONTROL MODE

To allow DMX control you need to:
1  Set switch 10 of the 

large switch block 
ON to choose DMX 
mode.

2  Select the required 

DMX base address 
using switches 1 to 
9 of the large switch 
block. Each of the nine switches is ‘weighted’ with a value as shown here. Numerous apps 
are available to assist you with configuring the correct switch combinations for a given 
DMX address. 

Note: The total number of DMX channels required for control will depend upon 

the chosen port grouping and fixture types (see “DMX channel layouts” on page 9).

Fixture type

6

3

5

2

4

1

ON

Port grouping

6

3

5

2

4

1

ON

3  Use switches 1 and 2 of the small switch block to 

choose the required grouping of channel outputs as 
required by the Aqua Drums being connected and 
their required functions. 

  1 

Port grouping

 OFF  OFF 

1 combined group of four ports

 ON  OFF 

2 groups of two ports

 OFF  ON 

4 separate ports

 ON 

ON 

4 separate ports

See “Port grouping” on page 8 for more details.

4  Use switches 4 and 5 of the small switch block to 

set the type of Aqua Drum fixtures being used:

  4 

Fixture type

 ON  OFF 

White

 ON 

ON 

RGBW/A   

Note: The chosen fixture type (RGBW/A or White) is 
applied globally to all ports. However, the electrical 
characteristics of the ports do not change (only their 
logical addressing configuration), so it is possible to 
mix white fixtures into an RGBW set up. As such, the 
various white emitters of the fixture would respond 
individually to the separate RGBW channel addresses.  

Summary of Contents for Aqua Drum EO































Reviews: