ACCES I/O Products, Inc.
MADE IN THE USA
mPCIe-ADIO16-8F Family Manual
2
Rev B1f
C
HAPTER
1:
Q
UICK
S
TART
It is recommended that you install the software package before
installing the PCI Express Mini (mPCIe) or M.2 card in your
computer. You can install the software
1
using our stand-alone
installer downloaded from the website.
Run the installer you downloaded and follow the prompts to install
the software for your device.
Please note: during the installation you may be prompted regarding
the installation of non-WHQL-certified drivers; please carefully
confirm the digitally signed source of the drivers and accept the
installation.
Once the software has been installed, shut down your system and
carefully install the mPCIe card.
Re-start your system. Once the computer finishes booting, your
new I/O should already be installed and ready for use; you can
confirm this by launching Device Manager and looking under the
“Data Acquisition” section. If, for any reason, the device displays a
warning triangle, right-
click and select “Update Driver”.
1
In Linux or OSX please refer to the instructions in those directories.
C
HAPTER
2:
I
NTRODUCTION
This manual is applicable to both the PCI Express Mini Card (mPCIe)
and M.2 card versions of this product. The registers, I/O and
performance specifications are the same.
•
PCI Express Mini Card (mPCIe) type F1 or M.2 type 2280/2260,
with latching I/O connector
•
16-bit, Bipolar, Differential, A/D converter
•
Software selectable as 8 Single-Ended (Pseudo-differential) or 4
Differential Inputs
•
7 channel-by-channel programmable differential input ranges
from ±0.3125V up to ±12V (48Vp-p)
•
Sustained sampling rates up to 1MHz
•
A/D starts via software, external input, or periodic timer
•
A/D “Scan Start” mode optimizes inter
-channel timing
•
High impedance, 8-
channel input: 1 MΩ
•
32k FIFO plus DMA for efficient, robust data streaming
•
Four 16-bit analog outputs
•
5 per-channel programmable ranges: 0V to 5V, 0V to 10V,
±2.5V, ±5V, ±10V
•
Outputs Drive ±10mA Guaranteed
•
16 Digital I/O; 8 individually configurable for input/output
•
Onboard Watchdog with status output
•
RoHS compliant standard
C
HAPTER
3:
H
ARDWARE
This manual applies to the following models:
VENDEV
mPCIe-ADIO16-8F mPCIe, A/D 16-bit, 1MHZ, 4 D/A
494F:C0EC
mPCIe-ADIO16-8A mPCIe, A/D 16-bit, 500KHZ, 4 D/A 494F:C0ED
mPCIe-ADIO16-8E mPCIe, A/D 16-bit, 250KHz, 4 D/A 494F:C0EE
mPCIe-ADI16-8F
mPCIe, A/D 16-bit, 1MHZ
494F:80EC
mPCIe-ADI16-8A
mPCIe, A/D 16-bit, 500KHZ
494F:80ED
mPCIe-ADI16-8E
mPCIe, A/D 16-bit, 250KHz
494F:80EE
mPCIe-ADIO12-8A mPCIe, A/D 12-bit, 500KHZ, 4 D/A 494F:C05C
mPCIe-ADIO12-8
mPCIe, A/D 12-bit, 250KHz, 4 D/A 494F:C05D
mPCIe-ADIO12-8E mPCIe, A/D 12-bit, 100KHz, 4 D/A 494F:C05E
mPCIe-ADI12-8A
mPCIe, A/D 12-bit, 500KHZ
494F:C05C
mPCIe-ADI12-8
mPCIe, A/D 12-bit, 250KHz
494F:C05D
mPCIe-ADI12-8E
mPCIe, A/D 12-bit, 100KHz
494F:C05E
These models are full-
length “F1”
mPCIe devices (30 × 50.95 mm).
All units are RoHS compliant.
INCLUDED IN YOUR PACKAGE
•
mPCIe-ADIO card
Available accessories include:
CAB-mPCIe-ADIO
9 inch panel-mount DB37M twisted pair cable
assembly
ADAP37F-MINI
Direct plug-on terminal board mates with
DB37M on CAB-mPCIe-ADIO
LF-BRK-P9259-37
Mounting bracket for DB37M on CAB-mPCIe-
ADIO
mPCIe-HDW-KIT2
Mounting hardware for 2mm
mPCIe-HDW-KIT2.5 Mounting hardware for 2.5mm
Contact the factory for information regarding additional accessories,
options, and specials that may be available to best fit your specific
application requirements, such as Industrial Temperature (-40°C to
85°C).
C
HAPTER
4:
C
ONFIGURATION
S
ETTINGS
All configuration of this device is performed through software; there
are no jumpers or switches to set.
