background image

 

English 

Notes on handling batteries 

 

Make sure that batteries are not in the hands of children. Children could put batteries in their 
mouths and swallow them. This can lead to serious damage to health. In this case consult a 
doctor immediately! 

 

Normal batteries must not be charged, heated or thrown into an open fire (danger of explosion!) 

 

Do not expose the battery to any heat source or direct sunlight and do not store it in a place with 
a very high temperature. 

 

The battery must not come into contact with water. 

 

The battery must not be disassembled, punctured or damaged. 

 

The battery contacts must not be short-circuited. 

 

Replace weakening batteries in good time. 

 

Always replace all batteries at the same time and use batteries of the same type. Ideally you 
should use identical batteries from the same manufacturer as those from the original scope of 
delivery, as the device has been intensively tested with these batteries and thus optimum 
function is ensured.  

 

Leaking or damaged batteries can cause burns on contact with skin. Use suitable protective 
gloves in this case. Clean the battery compartment with a dry cloth. 

 

Cleaning 

 

Dusty equipment must be cleaned. Dust deposits in the air slots can be sucked off or blown out. 
If necessary, the dust can be removed with a brush. 

 

The surface can be cleaned with a cloth slightly moistened with soapy water. Only use suitable 
microfibre cloths for high-gloss surfaces. 

 

Make sure that no water gets inside the device! 

 

Do not clean the appliance in the dishwasher! 

 

Do not use sharp, pointed, abrasive, corrosive cleaning agents or hard brushes! 

 

Do not use chemicals! 

 

Do not clean the device with easily flammable liquids! 

 

Notes on the disposal of the device 

Attention: The EU Directive 2012/19/EU regulates the proper return, treatment and 
recycling of used electronic equipment. This symbol means that, in the interest of 
environmental protection, the device must be disposed of at the end of its service life in 
accordance with the applicable legal regulations and separately from household and 
commercial waste.  The old device can be disposed of at the appropriate official 
collection points in your country. Follow local regulations when disposing of the 
materials. For further details about the withdrawal (also for non-EU countries), please 

contact your local administration. Separate collection and recycling conserves natural resources and 
ensures that all regulations for the protection of health and the environment are observed when 
recycling the product. 

 

 

Summary of Contents for PLBW10000



















Reviews: