background image

6

*Specifications are subject to changes without notice.

SYSTEM CONNECTION

1)  Connect HDMI sources (e.g. DVD) to HDMI input ports of the Matrix Switcher via good quality 

  HDMI cables.

2)  Connect the Pre-Installed CAT5e/CAT 6 cable infrastructure to Matrix Switcher and HDBaseT 

  receivers (HDBT-HD11RP) via good quality patch leads.

3)  Connect HDTV to HDMI output port via HDMI cable.

4)  Plug in an HDMI cable in to each of HDBT-HD11RP and connect to the local display [HDTV].

5)  Connect speaker to L&R (RCA) output port via audio cable.

6)  Plug the IR Receivers 3.5mm jack into the IR IN sockets on HDBT-HD11RP and plug in the  

  IR Emitters to the IR OUT sockets (1~4) on Matrix Switcher to make up as IR Matrix.

7)  Plug the phoenix connector in to the RS232 socket on the matrix, this will enable the Matrix 

  Switcher to be controlled via a PC.

8)  Plug in a Patch lead from the router in to the Ethernet port on Matrix Switcher to control Matrix 

  Switcher by TCP/IP protocol.

9)  Plug in the Power supply adapter 24V DC and tighten to secure. Once all components have 

  been connected and the installation is completed, switch on the mains supply at the socket.

Note:

● 

Connect HDBT ports of Matrix Switcher and far-end HDBT-HD11RP with a single straight cable.

● 

IR receivers connected to IR IN should be with carrier. If not, send

command %0900. or %0901.to activate native carrier mode or force carrier mode in

the IR matrix launched between Matrix Switcher and far-end HDBT-HD11RP.

The Matrix Switcher has 3 HDBaseT outputs which support PoC technology. Plug in the 4 RJ45 

patch leads in to the HDBT outputs and connect to the pre-installed infrastructure. Connect the 

HDBT-HD11RP HDBaseT Receiver/s to the pre-installed cabling via additional patch leads. Plug the 

power supply in to the power socket on the matrix, the HDBT-HD11RP will be powered by the Matrix 

Switcher.

Connection Proceduce

Connection with HDBaseT T Receiver

ABtUS

MAX-HDBT44/P

(back view)

Receiver

HDBT-HD11RP

HDMI Out

HDBT

 Out

Summary of Contents for MAX-HDBT44/P





























Reviews: