13 Power AC or DC +
14
Earth Ground
16 Power AC or DC –
14
13
15
16
Input Switch Settings, Wiring
APD 6380
6
5
7
8
Test Cal.
Span
Zero
Test
Output
Input
Loop
Tracker
APD 6380
AC to DC
Isolated Transmitter
Loop
Tracker
Output
0-1 V
0-2 V
0-4 V
1-5 V
0-5 V
0-8 V
2-10 V 0-10 V
±5 V
±10 V 0-2 mA 0-4 mA 0-8 mA 2-10 mA 0-10 mA 0-16 mA 4-20 mA 0-20 mA
Switches
ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE ABCDE
Input
0-4 mA
IA60V IA68V IA61V IA66V IA69V IA62V IA67V IA63V IA64V IA65V IA60I IA68I IA61I IA66I IA69I IA62I IA67I IA63I
0-5 mA
IA20V IA28V IA21V IA26V IA29V IA22V IA27V IA23V IA24V IA25V IA20I IA28I IA21I IA26I IA29I IA22I IA27I IA23I
0-7.5 mA
I2E0V I2E8V I2E1V I2E6V I2E9V I2E2V I2E7V I2E3V I2E4V I2E5V I2E0I I2E8I I2E1I I2E6I I2E9I I2E2I I2E7I I2E3I
0-10 mA
I220V I228V I221V I226V I229V I222V I227V I223V I224V I225V I220I I228I I221I I226I I229I I222I I227I I223I
0-12 mA
IA70V IA78V IA71V IA76V IA79V IA72V IA77V IA73V IA74V IA75V IA70I IA78I IA71I IA76I IA79I IA72I IA77I IA73I
0-15 mA
IA30V IA38V IA31V IA36V IA39V IA32V IA37V IA33V IA34V IA35V IA30I IA38I IA31I IA36I IA39I IA32I IA37I IA33I
0-20 mA
IB20V IB28V IB21V IB26V IB29V IB22V IB27V IB23V IB24V IB25V IB20I IB28I IB21I IB26I IB29I IB22I IB27I IB23I
0-25 mA
I820V I828V I821V I826V I829V I822V I827V I823V I824V I825V I820I I828I I821I I826I I829I I822I I827I I823I
0-30 mA
I230V I238V I231V I236V I239V I232V I237V I233V I234V I235V I230I I238I I231I I236I I239I I232I I237I I233I
0-40 mA
I060V I068V I061V I066V I069V I062V I067V I063V I064V I065V I060I I068I I061I I066I I069I I062I I067I I063I
0-50 mA
I020V I028V I021V I026V I029V I022V I027V I023V I024V I025V I020I I028I I021I I026I I029I I022I I027I I023I
0-60 mA
IB30V IB38V IB31V IB36V IB39V IB32V IB37V IB33V IB34V IB35V IB30I IB38I IB31I IB36I IB39I IB32I IB37I IB33I
0-75 mA
I830V I838V I831V I836V I839V I832V I837V I833V I834V I835V I830I I838I I831I I836I I839I I832I I837I I833I
0-80 mA
I960V I968V I961V I966V I969V I962V I967V I963V I964V I965V I960I I968I I961I I966I I969I I962I I967I I963I
0-90 mA
I3F0V I3F8V I3F1V I3F6V I3F9V I3F2V I3F7V I3F3V I3F4V I3F5V I3F0I I3F8I I3F1I I3F6I I3F9I I3F2I I3F7I I3F3I
0-100 mA
I920V I928V I921V I926V I929V I922V I927V I923V I924V I925V I920I I928I I921I I926I I929I I922I I927I I923I
0-117 mA
I0B0V I0B8V I0B1V I0B6V I0B9V I0B2V I0B7V I0B3V I0B4V I0B5V I0B0I I0B8I I0B1I I0B6I I0B9I I0B2I I0B7I I0B3I
0-120 mA
I330V I338V I331V I336V I339V I332V I337V I333V I334V I335V I330I I338I I331I I336I I339I I332I I337I I333I
0-125 mA
I090V I098V I091V I096V I099V I092V I097V I093V I094V I095V I090I I098I I091I I096I I099I I092I I097I I093I
0-150 mA
I030V I038V I031V I036V I039V I032V I037V I033V I034V I035V I030I I038I I031I I036I I039I I032I I037I I033I
0-175 mA
I140V I148V I141V I146V I149V I142V I147V I143V I144V I145V I140I I148I I141I I146I I149I I142I I147I I143I
0-200 mA
I120V I128V I121V I126V I129V I122V I127V I123V I124V I125V I120I I128I I121I I126I I129I I122I I127I I123I
Voltage Output
Switch E set to “V”
2
1
3
4
–
+
Voltage
Device
Current Sourcing Output
Switch E set to “I”
Current Sinking Output
Switch E set to “I”
AC Input
10
9
11
12
mVAC,
VAC or
mAAC
Voltage Input Range Selection
See table below (voltage inputs) and on the next page (current
inputs) to select I/O ranges for your application. It is generally
easier to select ranges before installation.
The module side label lists common ranges. See the model/
serial number label for module information, options, or if a
custom range was specified.
It may also be possible to use the next highest setting and trim
the output signal with the zero and span potentiometers.
Switch A: Set to "V" for voltage input
Switch B: Input range
Switch C: Input range
Switch D: Output range
Switch E: Set to "V" for voltage output or "I" for current
output
Note that when using a current shunt input, it measures a mV
drop across a fixed resistance, typically 50 mV, 75 mV or 100
mV. The correct input setting would be the appropriate mV
range for the shunt.
Current Input Range Selection
See table below to select I/O ranges when using a current
input. It is generally easier to select ranges before installation.
See the model/serial number label for module information,
options, or if a custom range was specified.
The module side label lists common ranges.
It may also be possible to use the next highest setting and trim
the output signal with the zero and span potentiometers.
Switch A: Set to "I" for current input
Switch B: Input range
Switch C: Input range
Switch D: Output range
Switch E: Set to "V" for voltage output or "I" for current
output
Voltage Output
Set switch E to "V" for a voltage output.
If your receiving device (such as a PLC or a display) uses a
voltage input, use terminals 3 and 4 as shown in the wiring
diagram.
Current Output
Set switch E to "I" for a current output.
Determine if your receiving device (such as a PLC or a display)
provides power to the current loop or if the loop must be pow-
ered by the APD module. Typical voltage may be 9-24 VDC at
your device's input terminals if it provides power to the loop.
If your device does not power the current loop, the APD can
provide power using terminals 3 and 4 as shown in the wiring
diagram.
If it provides power to the loop or an external supply provides
power to the loop, use terminals 2 and 3 aas shown in the
wiring diagram.
Module Power
Check model/serial number label for module operating voltage
to make sure it matches available power.
When using DC power, either polarity is acceptable, but for
consistency with similar API products, positive (+) can be wired
to terminal 13 and negative (–) can be wired to terminal 16.
Type of Device for Output
– Terminal + Terminal
Measuring/recording device
accepts a voltage input.
3 (
–)
4
(
+)
switch E
set to “V”
Measuring/recording device
accepts a mA (current) input and
the input is unpowered or pas-
sive. APD module provides the
loop power.
3 (
–)
4
(+20 V)
switch E
set to “I”
Measuring/recording device
accepts a mA (current) input and
provides power to the current loop.
2 (
–)
3
(
+)
switch E
set to “I”
To maintain full isolation
avoid combining power sup-
plies in common with input,
output, or unit power.
Cu 60/75°C
conductors
14 AWG
max.
api-usa.com
1220 American Way Libertyville, IL 60048
Phone:
800-942-0315
Fax: 800-949-7502
A
A
BSOLUTE
BSOLUTE
P
P
ROCESS
ROCESS
I
I
NSTRUMENTS
NSTRUMENTS
1
2 3 4
5 6 7 8
9
10
11
12
13 14
15
16
Input
Not used
Output
Power
Wire terminal
torque
0.5 to 0.6 Nm or
4.4 to 5.3 in-lbs
2
1
3
4
–
+
+
–
–
+
mA
Device
R
i
Loop
Power
Source
–
+20V
mA
Device
R
i
2
1
3
4
Not used
Module powers mA output loop
Module mA output is unpowered
3- or 4-wire transmitter
or 2 wire transmitter with
external power supply
mA output: determine if receiving device has
a passive or powered input. The module can
be wired for a sinking or sourcing mA output.
* Do not make connections
to unused terminals!
* Do not make connections
to unused terminals!
* Do not make connections to unused terminals!
