background image

Absco Industries

Assembly Instruction Manual

ABSCO GABLE CARPORT

MODEL: GCPDN2

6.0mW x 6.0mD x 2.98mH

Model: GCPDN2

8/06/23

6  

 

 

Guide for Connecting Frame Sections

Absco sheds’ frame assemblies are supplied with 
10-16x16 self drilling wafer head phillips drive tek 
screws
The wafer head minimises distortion to the sheet 
cladding once it is fi tted to the frame
Ensure that driver bits used to fasten these screws 
is phillips drive, as similar alternatives (EG. Pozi 
drive) increases the risk of stripping the head of 
these screws.

Some holes are pre-punched in Absco sheds’ frame 
sections, however the wide range of positions that 
most fasteners are required for means that the 
remainder have to be drilled as per the connection 
being made
A 3mm drill bit is supplied for pre-drilling holes 
where self drilling screws may be more diffi cult to 
establish holes with (EG. Fitment of purlin brackets).

Absco sheds’ frame sections are manufactured 
from light gauge steel, enabling for the notched 
ends or lengths of one frame section to be spread 
over the sides of another frame section, boxed 
frame section or H-section.

Absco sheds’ frame sections are designed to nest 
into one another to create boxed frame sections
Boxed frame sections are only required in some 
parts of the entire frame assembly
Boxed frame sections are fastened together using 
the fast014 tek screws supplied at 300mm centres 
(unless otherwise stated) along the length of each 
boxed frame section.

Some connections are designed to fasten more than two parts together. Connections may also not 
feature a defi ned alignment or physical stop.
For these reasons, focus on arranging all parts of a frame assembly or subassembly together (to 
the overall sizes and check measurements nominated) using minimal screws. This allows for easier 
adjustment to various connections which may be necessary to achieve the overall dimensions and 
check measurements that are nominated.
Fit the remaining screws once the frame assembly or subassembly is assembled as per the overall 
dimensions and check measurements that are nominated 

Boxing Frame Sections

A

A

BB

HIGH SIDE A

HIGH SIDE B

LOW SIDE B

LOW SIDE A

FAST014

FAST014

HIGH SIDE

HIGH SIDE

(PRINT)

(PRINT)

LOW SID

E

LOW SID

E

Summary of Contents for GCPDN2






















Reviews: