ABSCO SHEDS CYCWKUTK Assembly & Instruction Manual Download Page 1

Page: 1 / 24

Absco Industries

Assembly Instruction Manual

LARGE GABLE SHED

N3/C1 FRAME KIT

FOR WORKSHOP & UTILITY MODELS

Model: CYCWKUTK

02/03/21

1.3

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

LEAVE A REVIEW

Tell us about your experience and

receive a $20 Coles Gift Card.

Visit

www.abscosheds.com.au/review

AU: 1800 029 701

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

This kit is applicable to the following sheds:

The addition of this frame kit will increase the
wind rating of the specified sheds to

Wind rating: N3/C1 as per AS4055-2012.
Suitable for specific cyclonic regions

60303WK
52233WK
45302WK
45232WK

3060UTK
3052UTK
3045UTK

WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.

WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.

View of frame kit applied to

60303WK

Where information conflicts with the original
instruction manual, this document is to be
referenced.

This instruction manual is to be used during
the initial construction of the structure.

Summary of Contents for CYCWKUTK

























Search results

Summary of Contents for CYCWKUTK

Reviews:

Related manuals for CYCWKUTK

Brands by name

Popular brands

ABSCO SHEDS CYCWKUTK, Assembly & Instruction Manual

Search results

Summary of Contents for CYCWKUTK

Reviews:

Related manuals for CYCWKUTK

Brands by name

Popular brands