background image

TROUBLE SHOOTING    

 

11

 

Fault Possible 

Cause 

Remedy 

The mixer does not 
stop 

Electrical / mechanical 
malfunction. 

Switch off power at 
main switch. Isolate 
mixer by removing 
wall plug. 

 
Attach danger tag to 
machine. 

 
Contact service 
agent. 

Bread dough too soft. 

Excessive water used in 
dough (human error). 
 

 
Incorrectly metered / 
measured through water 
meter (equipment error). 

 
Over-mixed dough 

Review recipe and 
adjust dough 
consistency. 

 
Contact authorized 
service agent. 

 
Review /check 
/change mix cycle. 

Final dough temperature 
too hot. 

Water temperature too 
hot. 

 
Dough mixed too long. 

Reduce water 
temperature. 

 
Shorten mix cycle. 

Final dough temperature 
too cold. 

Water temperature too 
cold. 

 
Dough mixed too shot. 

Increase water 
temperature. 

 
Lengthen mix time. 

Dough is difficult to 
remove from the mixing 
bowl. 

 
Dough left in bowl too 
long. 

 
Dough too soft. 

 
 
Dough over-mixed. 

Remove from bowl 
earlier. 

 
Refer-dough too 
soft. 

 
Run food grade oil 
between dough and 
bowl at the end of 
mix cycle to stop 
dough sticking. 

Summary of Contents for ABSFBM-50






















Reviews: