ABONG SEBRINGVILLE 3157826 Manual Download

Page: 27 / 97

22.

Place a “SHORT” section of tube into the tool (AL) and

slip on a spacer ring (DF). Do not glue!

23.

Apply CA glue to the joint between the spacer ring

(DF) and the tube.

24.

Press a pulley flange (DI) onto the spacer ring (DF),

marked side up.

25.

Apply CA glue to the face of the pulley flange (DI)

inside the marked ring. Press the pulley core (CF) onto

the pulley flange (DI).

26.

Apply CA glue to the face of the second pulley flange

(DI), inside the marked ring. Press the pulley flange

(DI) glue side down onto the pulley.

27.

Apply CA glue to the joint between the tube and the

pulley flange (DI). Press a spacer ring (DF) onto the

pulley flange.

Summary of Contents for SEBRINGVILLE 3157826


































































































Search results

Summary of Contents for SEBRINGVILLE 3157826

Reviews:

Related manuals for SEBRINGVILLE 3157826

Brands by name

Popular brands

ABONG SEBRINGVILLE 3157826, Manual

Search results

Summary of Contents for SEBRINGVILLE 3157826

Reviews:

Related manuals for SEBRINGVILLE 3157826

Brands by name

Popular brands