background image

Ap1200 Users’ Guide Page 3 of 14

CONTACT DETAILS

Address:

Able Systems Limited
Denton Drive
Northwich
Cheshire
CW9 7TU
England

UK Call:

01606 48621

USA Call:

1 706 207 3320

International Call:

+44 1606 48621

Fax:

+44 (0) 1606 44903

Email:

[email protected]

World Wide Web:

www.able-systems.com

INTRODUCTION

This document is a User Guide, written for the person connecting and using the ABLE Systems
Ap1200 printer.  Please read this Guide carefully before making any connection, opening the doors or
installing the printer.

3.1 

PROGRAMMERS GUIDE

A separate document, the ‘

Programmers Guide for the Ap1200 Printer

’, providing details of the control

codes, and describing the internal operation of this product is available.

3.2 

COPYRIGHT AND CONFIDENTIALITY NOTICE

ABLE Systems Limited property is subject to copyright. This includes single chip controller firmware,
layout diagrams, circuit diagrams, pin connection lists, application data.

Other property may also be subject to copyright. However, you may copy this leaflet if you are an
ABLE Systems customer AND the copy is for your own use.
If you want to copy information to anyone else then you must first obtain permission from ABLE
Systems.

No warranty in respect of patent rights of ABLE Systems or of third parties is given.
You must not amend or copy controller firmware. You may be prosecuted if you do.

The Ap1200 printer is design registered in the UK (No 2092320), in France (No 004938) and in the
USA (US Design Patent No D466919).  You must not copy it or offer copies for sale.

Product Safety is a serious issue.

Read the 

Product Safety

 section before using these products.

In case of doubt, refer to ABLE Systems.

Summary of Contents for Ap1200















Reviews: