ABL eMH1 513 Instruction Manual Download Page 9 | Manualshive

Page: 9 / 20

ABL eMH1 513 Instruction Manual Download Page 9

IntroductIon

1

Introduction

This operating manual contains important information about the installation and safe

operation of the device. Please make sure to read and observe the safety instructions

provided.

All safety information in this operating manual must be passed on to all users.

Meaning of the safety information

DANGER!

Failure to heed this warning may lead to death or serious injury.

WARNING!

Failure to heed this warning could damage the device or any appliance

connected to it.

NOTE!

This symbol refers to recommendations or special features.

General safety information

The device has been manufactured according to current technical standards and safety

regulations. Failure to adhere to the safety instructions and advice may lead to electric

shock, burns and/or serious injuries.
The device may only be used if it is in a technically sound condition. Any faults com-

promising the safety of the device or anyone using it may only be repaired by qualified

personnel.

Warnings

The symbols and warning signs displayed on the charging station have the following

meanings:

«
...
7
8
9
10
11
...
»

Summary of Contents for eMH1 513





















Reviews:

No comments