Abit BF6 User Manual Download Page 24

Page: 24 / 106

2-14

Chapter2

BF6

FDC1 Connector

This 34-pin connector is called the “

floppy

disk drive connector

”. You can connect a

360K, 5.25”, 1.2M, 5.25”, 720K, 3.5’’,

1.44M, 3.5” or 2.88M, 3.5” floppy disk

drive, you can even connect a 3 Mode

floppy disk drive (it’s a 3 1/2” drive used in

Japanese computer systems).

A floppy disk drive ribbon cable has 34

wires and two connectors to provide for the connection of two floppy disk drives. After

connecting the single end to the FDC1, connect the two connectors on the other end to the

floppy disk drives. In general, people only install one floppy disk drive on their computer

system.

Note

A red mark on a wire typically designates the location of pin 1. You need to align the

wire pin 1 to the FDC1 connector pin 1, then insert the wire connector into the FDC1

connector.

IDE1 and IDE2 Connectors

An IDE hard disk drive ribbon cable has 40

wires and two connectors to provide a

connection for two IDE hard disk drives.

After connecting the single end to the IDE1

(or IDE2), connect the two connectors on

the other end to the IDE hard disk drives (or

CD-ROM drive, LS-120, etc.).

Before you install a hard disk, there are

some things you need to be aware of:

♦

“Primary” refers to the first connector on the motherboard, that is, the IDE1 connector on

the motherboard.

♦

“Secondary” refers to the second connector on the motherboard, that is, the IDE2

connector on the motherboard.

♦

Two hard disks can be connected to each connector:

Summary of Contents for BF6











































































































Search results

Summary of Contents for BF6

Reviews:

Related manuals for BF6

Brands by name

Popular brands

Abit BF6, User Manual

Search results

Summary of Contents for BF6

Reviews:

Related manuals for BF6

Brands by name

Popular brands