Abit BF6 User Manual Download Page 17

Page: 17 / 106

Installing the Motherboard

2-7

User’s Manual

ATX: ATX Power Input Connector

Caution

If the power supply connectors are not properly attached to the ATX power supply, the

power supply or add-on cards may be damaged.

Attach the connector from the power supply

to the ATX connector here. Remember you

have to push the connector from the ATX

power supply firmly to the end with the

ATX connector, insuring that you have a

good connection.

Note: Watch the pin position and the

orientation

FAN1, FAN2 & FAN3: FAN header

Attach the connector from the individual

CPU fan to the header named FAN1, and

attach the connector from the chassis fan to

FAN2 or & FAN3 header.

You must attach the CPU fan to the

processor, or your processor will work

abnormally or may be damaged by

overheating. Also, if you want the computer

case’s internal temperature to be kept steady and not too high, you had better connect the

chassis fan to reach this goal.

Note: Watch the pin position and the orientation

Summary of Contents for BF6











































































































Search results

Summary of Contents for BF6

Reviews:

Related manuals for BF6

Brands by name

Popular brands

Abit BF6, User Manual

Search results

Summary of Contents for BF6

Reviews:

Related manuals for BF6

Brands by name

Popular brands