background image

AI-Vue Camera Quick Start Guide 

 

16 

 

Declaration of toxic and hazardous substances in electronic and electrical products 

設備名稱

(Equipment name) : 

AI-Vue 

自動對焦槍型網路攝影機

 

型號(型式)

Type designation (Type): 

VS1NL70/VS1NN60

 

單元

 

nit 

限用物質及其化學符號

 

Restricted substances and its chemical symbols 

 

 

 

六價鉻

 

多溴聯苯

 

多溴二苯醚

 

Lead (Pb) 

Mercury (Hg) 

Cadmium (Cd) 

Hexavalent 

chromium 

(Cr+6) 

Polybrominated 

biphenyls 

(PBB)

 

Polybrominated 

diphenyl ethers 

(PBDE)

 

PCBA

 

 

○ 

○ 

○ 

○ 

○ 

塑膠件

 

○ 

○ 

○ 

○ 

○ 

○ 

金屬件

 

○ 

○ 

○ 

○ 

○ 

○ 

Cable 

○ 

○ 

○ 

○ 

○ 

○ 

Adapter 

○ 

○ 

○ 

○ 

○ 

○ 

電池

 

 

○ 

○ 

○ 

○ 

○ 

備考

1.

〝超出

0.1 wt %

〞及〝超出

0.01 wt %

〞係指限用物質之百分比含量超出百分比含量基準值

 

Note 1

“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance 

exceeds the reference percentage value of presence condition. 

備考

2.

〞係指該項限用物質之百分比含量未超出百分比含量基準值。

 

Note  2

“○”  indicates  that  the  percentage  content  of  the  restricted  substance  does  not  exceed  the  percentage  of 

reference value of presence. 

備考

3.

〝-〞係指該項限用物質為排除項目。

 

Note 3

The “−” indicates that the restricted substance corresponds to the exemption.

 

 

Summary of Contents for AI-Vue VS1NL70

















Reviews: