background image

ABI Classic Spreader Setup Guide 

ABI(

Absolute Innovations, Inc.

)      -      855-211-0598      -      www.abiattachments.com 

Operating Levers:  

 

 

Chain engagement Mechanism:  

 

 

Apron adjustment: 

 

 
 
 

 

The operating levers engage the apron chain as well 
as the beater bars. The operation lever labeled #1 is 
used to engage and disengage the apron chain. 
There are 4 speeds to choose from when engaging 
the apron chain for use. The top slot is fully 
disengaged and the bottom slot is fully engaged. To 
engage either lever squeeze the latch handle fully, 
and lower the lever. Make sure the latch is fully set 
in its slot before operating the Spreader. When the 
spreader is not in being used to spread, set the 
levers back to the disengaged position; for 
transporting. 

 

 

 

The operating lever labeled #2 in the above photo 
controls the chain engagement mechanism. This 
allows the chain to be disengaged and engaged one 
tooth at a time and helps keep the chain and 
sprocket in alignment. This also helps reduce 
unneeded repair, wear and tear, and breakage. 

 

 

To adjust the apron chain you will need to loosen the 
two bolts labeled #1 in the attached photo. Then 
turn the adjustment nut labeled #2 to adjust the 
tension on the apron chain. For proper tension on 
your apron chain you want to have no more than 

3” 

of lift in the middle of the bed, on the apron chain. 
You will need to make this adjustment to both sides 
of the apron chain. Make sure to keep track of how 
many times you turn the adjustment nut. To keep 
the apron level you must adjust both sides of the 
apron chain the same amount.  

** Once you have adjusted the apron chain 
remember to retighten bolt set #1 before use.   

  

#1 

#2 

#2 

#1 

Summary of Contents for 85G














Reviews: