Abex Exhibit Systems • 355 Parkside Drive, San Fernando, CA 91340 • (800) 537-0231
PAGE 1
Profile
Label
001
Description
1/4" ALUMINIUM OVAL BASE PLATE 17.5" (444.5MM) x 4.72" (120MM)
#
2
002
003
M1901 30" (762MM) EXTRUSION W/ (1) 50° CUT, (2) HOLES FOR BASE PLATE & LIGHTS
M1901 47.5" (1206MM) EXTRUSION W/ (1) 50° CUT
1
1
FRONT VIEW
TOP VIEW
17 1/2"
004
M1901 47.5" (1206MM) EXTRUSION W/ (1) 45° CUT, POWER SUPPLY
1
006
1
4
Z966 90° CORNER INTERNAL CONNECTOR
M1901 47.5" (1206MM) EXTRUSION W/ (1) 40° CUT
007
1
M1901 47.5" (1206MM) EXTRUSION W/ (1) 45° CUT
008
1
1. Slide straight connector (Z967) into inner channel of
extrusion.Turn screw enough to hold connector in place.
2. Take another extrusion and slide onto straight connector.
Tigthen both screws to connect extrusions together.
3. Repeat above steps to connect all spliced extrusions
together.
4. Slide corner connector (Z964 & Z965) into both sides of
horizontal extrusions.Turn each screw enough to hold
connector in place.
6. Slide vertical extrusions onto corner connectors of top
horizontal extrusion. Turn each screw enough to hold connector
in place.
7. Finish frame assembly by sliding corner connectors of bottom
horizontal extrusion into inner channel of vertical extrusions and
tighten the screws to secure frame extrusions together.
M1901 30" (762MM) EXTRUSION W/ (1) 45° CUT, (2) HOLES FOR BASE PLATE & LIGHTS
M1901 43.25" (1099MM) EXTRUSION W/ (1) 40° CUT, (1) 45° CUT & LIGHTS
009
1
010
1
Z4400 6" (152MM) EXTRUSION W/ (1) 5° CUT & (1) TENSION LOCK
012
1
Z4400 44.4" (1128MM) EXTRUSION W/ (1) 5° CUT & (1) TENSION LOCK
1
005
1
M1901 1.46" (37MM) EXTRUSION W/ (2) STRAIGHT CONNECTORS
011
1
5/16-18 FLAT HEAD SCREW 0.75" LONG FOR BASE PLATES
4
2
60"W (1524MM) x 95"H (2413MM) DYESUB GRAPHIC W/ SEG WELT ON ALL 4 SIDES
1
Z966/V ADJUSTABLE INTERNAL CONNECTOR
4
Z964 ADJUSTABLE CORNER INTERNAL CONNECTOR
60"
95"
43 1/4"
96 7/16"
Z966/V - Adjustable Connector
NOTE: Remove corner connectors
from exrtrusions before packing
Insert connector into short piece first
and tighten screw using Torx tool
(included). Do not overtighten.
Repeat procedure for long piece.
Loosen the screws on base plate but
do not remove them. Than swivel
base plates.
Bottom view
Tighten both screw firmly.
Bottom view
Z965B - Corner Connector
Z964 - Adjustable Corner Connector
NOTE: Remove corner connectors
from exrtrusions before packing
Connect frame extrusions together,
as shown, using Torx tool
(included). Do not overtighten.
Z967 - Straight Connector
NOTE: Remove connectors
from beams before packing
Connect frame spliced extrusions
together, as shown, using Torx tool
(included). Do not overtighten.
Z961/13 - Tension Lock
Tension Lock
Torx Tool
Place tension lock into groove.
Insert Torx 30 wrench and turn
1/2 turn
Z4400 46.08" (1170.4MM) EXTRUSION W/ (2) TENSION LOCKS
E460 42" (1067MM) PLASTIC WIRE MANAGEMENT
1
E460 28" (711MM) PLASTIC WIRE MANAGEMENT
4
Z967 STRAIGHT INTERNAL CONNECTOR
001
001
002
003
005
004
006
007
Power
Supply
008
009
Wire
Management
010
011
012
#LWT-EXT
Extrusion with (2) Z967
Straight Connectors
(2) Z964
(2) Z965B
(2) Z967
(2) Z964
(2) Z967
Wire
Management
