background image

Abex Exhibit Systems •   355 Parkside Drive, San Fernando, CA 91340   •   (800) 537-0231

PAGE  1

Tighten  both  screw  firmly.

Loosen the  screws on  base  plate but 
do  not  remove  them.  Than  swivel 
base  plates.

Bottom  view

Bottom  view

Z965  -  Corner  Connector

Z967  -  Straight  Connector

NOTE:  Remove  connectors 
from  beams  before  packing

NOTE:  Remove  corner  connectors 

from  exrtrusions  before  packing

Connect  frame  spliced  extrusions 
together, as  shown,  using  Torx  tool 
(included).  Do not  overtighten.

Connect  frame  extrusions  together, 
as  shown,  using  Torx  tool 
(included).  Do not  overtighten.

001

001

002

003

005

004

Z965  -  Corner  Connector  (2)

006

007

Power  Supply

Wire  Managment  Hole

Z967  -  Straight  Connector  (2)

Z967  -  Straight  Connector

Z961/13 -  Tension  Lock

NOTE:  Remove  connectors 

from  beams  before  packing

Connect  frame  spliced  extrusions 
together, as  shown,  using  Torx  tool 
(included).  Do not  overtighten.

Tension  Lock

Torx  Tool

Place  tension lock  into  groove.
Insert  Torx 30  wrench and  turn 
1/2  turn

Slide straight connector (Z967) into inner channel of 
extrusion.Turn   screw enough to hold connector in place.
Take another extrusion and slide onto straight  connector. Tigthen 
both screws to connect extrusions together.
Repeat above steps to connect all spliced extrusions together.
Slide corner connector (Z966) into both sides of horizontal 

extrusions.Turn each screw enough to hold connector in place.
Slide vertical extrusions onto  corner connectors of  top horizontal 
extrusion. Turn each screw enough to hold connector in place. 

Finish frame assembly by  sliding corner connectors of bottom 
horizontal extrusion  into inner channel of  vertical extrusions  and 
tighten the screws to secure frame extrusions together.

Z967  -  Straight  Connector

008

009

Wire  Managment

Z961/13 -  Tension  Lock

Z961/13 -  Tension  Lock

011

010

001

Wire  Managment

012

025

026

013

027

LIGHTS DETAILS

Lights  come  attached  to  extrusions.  Ensure all  lighting  strips  are  connected. 
Once  frame  is  assembled,  connect  strip-to-power  cords to  the end  of top 
and  bottom  lights  chain.
-  For  bottom  lights  connect  strip-to-power cord  to  power  supply  directly.  
-  For top  lights  connect  extension  cord to  strip-to-power  cord  and run  with 
wire  managment  extrusion  then  connect to  power  supply.
Run AC  power cord  out  through  grommet  hole  on  vertical  upright and 
connect  to  power  outlet.
T o  remove  or  re-attach  light  strips  use  provided  thumbscrews  with  plate. 

Strip-To-Power  Cord

EXtension  Cord 12ft

001

001

001

014

015

016

017

019

020

018

021

022

023

024

1.

2.

3.

4.

5.

6.

Power  Supply

Summary of Contents for LUMIWALL








Reviews: