ABERLINK Axiom Too Installation Manual Download Page 17 | Manualshive

Page: 17 / 21

background image

ABERLINK LTD

|

VATCH LANE

|

EASTCOMBE

|

GLOUCESTERSHIRE

|

GL6 7DY

|

UK

Tel : +44 (0)1453 884461

|

Fax : +44 (0)1453 882348

|

Email : [email protected]

|

Web : www.aberlink.com

Registered in England No. 7642245

|

VAT Registration No. GB 108 3075 37

Motorised Probe Heads

The same connections apply to the PHC10-3, except the unit now fits into front of bench.

Switch ON

Connect main air supply and switch on the controller.

Sequence of events.

1.

Open system.cfg in windows and place “;” this symbol in front of the
system_action= lines. (File save)

2. Start up axis tuner program,
3. Bear in mind the counterbalance is not set, it may drop depending where the z is

located. Hold the Z axis by hand.

4. Switch on the amp and air on (outputs 9 and 10)

Probe head connection, cable
from the machine, 15 way
socket.

RS232 Connection, connect
supplied lead. The other end
of this cable connects to the
comm. port on the PC

PICS connection, connect supplied
lead. The other end plugs into the
probe connector on the PC

«
...
15
16
17
18
19
...
»

Summary of Contents for Axiom Too






















Reviews:

No comments

Related manuals for Axiom Too

TUNICS T100S-HP

Brand: Yenista Optics Pages: 66

Brand: 3nh Pages: 10

Brand: Bacharach Pages: 87

Brand: PAT Pages: 57

Brand: Det-Tronics Pages: 18

Brand: ACCRETECH Pages: 104

Vigilant Plant MR20000

Brand: YOKOGAWA Pages: 230

Brand: Omega Pages: 59

Panel Scope VPS10

Brand: Velleman Pages: 60

Brand: jbc Pages: 12

Brand: AquaMetrix Pages: 37

Brand: novomatics Pages: 39

Brand: LaserLine Pages: 11

Brand: 3nh Pages: 32

Brand: NARDA Pages: 60

Backsense BS-9000-WD

Brand: Brigade Pages: 42

Brand: Cargo Data Pages: 3

Brand: GeoMax Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands