ABB Zenith ZTS T Series Quick Start User Manual Download Page 9

Page: 9 / 44

Feature comparison

ZTS(D) controls (Touch screen)

Invalid frequency

Yes

Incorrect phase sequence

Yes

Features

Controls

Touch + keys

LED indications for ATS, S1 and S2 status

Yes

Open transition - Standard digital inputs/outputs

2 / 1

Delayed transition - Standard digital inputs/
outputs

3 / 1

Programmable digital inputs/outputs

Yes

Auto config (voltage, frequency, phase system)

Yes

Auto config (voltage frequency, phase system)

Yes

Source priority

SOURCE 1/2, No priority

Manual re-transfer

Yes

In-phase monitor

Yes

Genset exercising: on-load, off-load

Yes

In-built power meter module

Yes

Load shedding

Yes

Real time clock

Yes

Event log

Yes

Predictive maintenance

Yes

Harmonics measuring

Voltage, current

Field-mount accessories

Auxiliary contacts for position indication

Yes

Digital input/output modules

Yes

12-24 Vdc aux supply module for controller

Yes

Communication modules

Yes

Connectivity

Modbus RS485

Yes

Modbus/TCP

Yes

Profibus DP

Yes

ProfiNet

Yes

DeviceNet

Yes

Ethernet IP

Yes

Ekip Com Hub (monitoring via ABB Ability

™

: EDCS)

Yes

Enclosures

Type 1, 3R, 4, 12, and 4X

Yes

For applications

Mains - Mains

Yes

Mains - Generator

Yes

Contact ABB for applications with smaller than 20 KVA gensets.

—
Table 2 ATS features not limited to what is in the table above

Summary of Contents for Zenith ZTS T Series













































Search results

Summary of Contents for Zenith ZTS T Series

Reviews:

Related manuals for Zenith ZTS T Series

Brands by name

Popular brands

ABB Zenith ZTS T Series, Quick Start User Manual

Search results

Summary of Contents for Zenith ZTS T Series

Reviews:

Related manuals for Zenith ZTS T Series

Brands by name

Popular brands