manualshive.com logo in svg

ABB XSeriesG4, User Manual

Share
Download
ABB XSeriesG4 User Manual Download Page 86

 

74 

Description 

Spare Part Number 

Battery Charger 115 Vac/12 Vdc  

2011720-007 

Battery Charger 230 Vac/12 Vdc 

2011720-008 

Power Supply Converter 120 Vac/Vdc 

2018200-004 

Power Supply Converter 240 Vac/Vdc 

2018200-005 

Battery Charger 115 Vac/12 Vdc 

2100269-001 

Battery Charger 230 Vac/12 Vdc 

2100269-002 

Communication Mounting Bracket 

2015260-005 

 

Replacing the lithium battery 

This section presents the procedures for replacing the onboard lithium battery which maintains the SRAM memory. Replacing 
the lithium battery should only be done while the flow computer is fully powered by the battery pack or charging system. SRAM 
memory stores historical flow data. 

 

Step-by-step instructions 

 

NOTICE 

– Property damage.

 Loss of power to the unit will perform a COLD start when lithium battery is 

removed. All data and configuration files will be destroyed. 

  Collect data from the unit. 

  Back up configuration files following the instructions listed in section 4.2

, Backing up configuration files

. 

  Gain access to the Main Processor Board by unlatching the enclosure door (see Figure 68: 

XRC

G4

 6490 

component/cable locations

 and Figure 69: 

XRC

G4

 6890 component/cable locations

). 

  Remove the lithium battery cover from the battery bracket by inserting the flat blade of a small screwdriver between the 

cover and the side of the bracket. This should free the cover from the bracket allowing access to the battery.  

  Grasp the battery on each side and pull from the bracket. Note the positive end of the battery is at the bottom end of the 

bracket. 

  Insert a new lithium battery into the bracket with the positive end of the battery down. 

  Replace the battery cover. 

 

Replacing the XRC

G4

 battery pack 

This section presents the procedures for removal and installation of the XRC

G4

 battery pack. To access the battery pack, open 

the XRC

G4

 door. The battery pack is located behind the front-mounted keeper plate (model 6490 only). 

 

NOTICE 

– Property damage.

 When removing the battery pack, do not remove the lithium battery from the main 

electronic board (XRC

G4

 board). This prevents any data stored in board RAM, from being lost. Removing the CPU 

engine card will also result in a COLD boot (loss of data stored in RAM). 

 

Step-by-step instructions 

  Make sure the J1 (Figure 70) memory backup jumper covers the top two pins to enable the memory backup. 

Summary of Contents for XSeriesG4





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands