ABB TPL65VA33 Operation Manual Download

Page: 57 / 124

Operation Manual / TPL65VA32/33

Maintenance

Cleaning the filter silencer

5.2

Page 55

ber

2016

L2464_

ion

Removing and cleaning filter silencer



Remove filter strip (81265).



Rinse filter strip (81265) using water with detergent additive or, if very

dirty, soak it and squeeze out carefully. Rinse it in cold water. Avoid

rough treatment (not a jet of water).

NOTICE

How dirty the filter strip (81265) is, depends on how clean the drawn-in

air is. Clean filter strip every 500 hours of service or more frequently if

necessary.



Unscrew and remove lock nuts (81273).



Unscrew and remove screws (81272) for connecting rods (81269).



Remove connecting rods (81269).



Carefully remove cover grids (81266).



Pull out insert units (E), bend open sheet-metal coverings (81137) and

then remove absorption segments (81136).



Clean the absorption segments (81136).

During cleaning, ensure that the absorption segments (81136) are only

cleaned with a mild jet of compressed air, soft brush or a damp cloth.

Otherwise there is a risk of damage or deformation.

NOTICE

Replace heavily contaminated or damaged parts with original parts from

ABB Turbo Systems.

If provided

Summary of Contents for TPL65VA33





























































































































Search results

Summary of Contents for TPL65VA33

Reviews:

Related manuals for TPL65VA33

Brands by name

Popular brands

ABB TPL65VA33, Operation Manual

Search results

Summary of Contents for TPL65VA33

Reviews:

Related manuals for TPL65VA33

Brands by name

Popular brands