ABB TPL65VA33 Operation Manual Download

Page: 116 / 124

Operation Manual / TPL65VA32/33

Mothballing the turbocharger

Taking the engine out of operation for

up to 12 months

10.1

Page 114

ber

2016

L2464_

ion

If the total acid number (TAN) is greater than 2 mg KOH/g, the following

mothballing measures are necessary after taking an engine out of opera-

tion:



Dismantle the turbocharger.



The rotor and the bearing parts must be removed by an official ABB

Turbocharging service station and refitted afterwards.



Clean all parts.



Machined, bright surfaces of steel and cast parts must be oiled with

anticorrosive oil.



Reassemble complete turbocharger.

Rotor turning in stack draught

If the rotor turns as a result of the stack draught:



Install blind flange between compressor casing outlet flange and

charge air duct.

Summary of Contents for TPL65VA33





























































































































Search results

Summary of Contents for TPL65VA33

Reviews:

Related manuals for TPL65VA33

Brands by name

Popular brands

ABB TPL65VA33, Operation Manual

Search results

Summary of Contents for TPL65VA33

Reviews:

Related manuals for TPL65VA33

Brands by name

Popular brands