ABB MRP31.0 Technical Description Download | Manualshive

Page: 6 / 24

background image

- 6 -

MRP31.0 Technical description

Issue: 09.2014

Power

MRP31

Mechanical Installation

The Modbus adapter module MRP31 can be mounted either on the UMC100.3 itself or separately from the UMC100.3 using the
single mounting kit (SMK3.0).

Mounting the MRP31 on the UMC100.3

When the module is installed directly on the UMC100.3 the UMC100.3 with MRP31 acts like a device with integrated Modbus
RTU communication. No additional accessories are needed.

Move down MRP31 until
snapped-in to fi x MRP31
on UMC100.3

Image shows UMC100.3 DC

«
...
4
5
6
7
8
...
»

Summary of Contents for MRP31.0

























Reviews:

No comments

Related manuals for MRP31.0

Brand: YASKAWA Pages: 256

Brand: Eaton Pages: 100

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: Federal Signal Corporation Pages: 34

Brand: SOMFY Pages: 112

Brand: K&K Pages: 10

iEP-5000G Series

Brand: ASROCK Pages: 2

Brand: Runxin Pages: 4

MultiConnect Dragonfly MTQ-MNA1-B01

Brand: Multitech Pages: 45

Brand: Zander Aachen Pages: 44

Brand: 4D systems Pages: 6

Brand: Variotech Pages: 24

MAXinBOX 24 ZIO-MB24

Brand: Zennio Pages: 24

Brand: Genius Pages: 52

Brand: Vixen Horns Pages: 2

Brand: CLS Pages: 6

EduTrainer 8071407

Brand: Festo Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands