background image

OI/LMS100-EN Rev

. A  12.2014

Contact us

ABB Inc. 

18321 Swamp Road
Prairieville, LA 70769 USA
Phone: +1 225 673 6100
Service: +1 225 677 5836
Fax: +1 225 673 2525
E-mail: [email protected]
Service e-mail: [email protected]

ABB Inc.

585, Boulevard Charest E., Suite 300
Quebec, QC Canada G1K 9H4
Phone: +1 418 877 2944
Service: +1 800 858 3847
Fax: +1 418 877 2834
E-mail: [email protected]
Service e-mail: [email protected]

ABB Engineering (Shanghai) Ltd.

No. 5, Lane 369, Chuangye Road
Kangqiao Town, Pudong District                                          
Shanghai, 201319, P.R. China
Phone: +86 10 64231407
Service: +86 21 61056421
Fax: +86 10 64371913
E-mail: [email protected]
Service e-mail: [email protected]

ABB Limited

Salterbeck Trading Estate
Workington, Cumbria, England CA14 5DS
Phone: +44 7885333752
Service: +44 145 3826661
E-mail: [email protected]
Service e-mail: [email protected]

www.abb.com/level

Note
We reserve the right to make technical changes or 
modify the contents of this document without prior 
notice. With regard to purchase orders, the agreed
particulars shall prevail. ABB does not accept any 
responsibility whatsoever for potential errors or 
possible lack of information in this document.

We reserve all rights in this document and in the 
subject matter and illustrations contained therein. 
Any reproduction, disclosure to third parties or 
utilization of its contents - in whole or in parts – is 
forbidden without prior written consent of ABB.

Copyright© 2014 ABB
All rights reserved

3KXL130100R4201

Sales

Service

Summary of Contents for LMS100 Series

















Reviews: