manualshive.com logo in svg

ABB KM26, Operating Instruction

Share
Download
ABB KM26 Operating Instruction Download Page 27

27

KM26 | 

MAGNETIC LEVEL GAUGE  |  OI/KM26-EN REV I

 . . . 5     Service and Maintenance

KM26 bargraph replacement glass 

installation procedure

1 

Remove old bargraph and tube holders from scale

2 

Assemble new bottom tube holder to scale using #6-32 
machine screw. Note orientation of grooves in tube 
holder that interface with matching feature on scale 
channel

3 

Insert one (1) rubber bumper into bottom tube holder. 
Rubber bumper should rest flat in holder cavity.

4 

Carefully align new class bargraph into scale channel and 
lower into bottom tube holder. Flat faces on glass tube 

should register with corresponding flat faces in cavity of 
bottom tube holder. Ensure glass tube rest flat on rubber 
bumper and it firmly seated. Nipple on bottom end glass 
of glass tube should protrude through slot in rubber 
bumper.

5 

Place one (1) rubber bumper on top of glass tube

6 

Align top tube holder with scale channel and slide down 
until top surface of holder is flush with top of scale 
channel. Screw hole should align with hole in holder

7 

Use #6-32 machine screw to lock machine screw to lock 
top tube holder in place

8 

Tighten nuts and install second nut to lock tube holders 
in place.

Figure 30- KM26 bargraph replacement glass installation procedure

Summary of Contents for KM26





































Reviews:

No comments

Brands by name

Popular brands

Load more brands