ABB IRB 5720 Product Manual Download

Page: 71 / 610

3.3.4 Orienting and securing the robot

General

This section describes how to orient and secure the robot to the base plate or
foundation in order to run the robot safely.

Attachment screws

The table below specifies the type of securing screws and washers to be used for
securing the robot to the base plate/foundation.

M24 x 100

Suitable screws

8 pcs

Quantity

8.8

Quality

4 mm flat washer

Suitable washer

Guide pins are required if mounting the manipulator to a
track motion or to a base plate.

25g6

12k6

(A)

XX1500000248

Cylindrical guide pin

Guide pins

550 Nm (screws lubricated with Molykote 1000)

Tightening torque

600-725 Nm, typical 650 Nm (screws none or lightly lubric-
ated)

90% (v=0.9)

Screw tightening yield point
utilization factor (v) (according
to VDI2230)

0.3 mm

Level surface requirements

Securing a floor mounted robot

Use this procedure to orient and secure the robot floor mounted.

Note

Action

Make sure the installation site for the robot con-
forms to the specifications in section

Technical

data on page 37

The hole configuration of the base
is shown in the figure in

Hole con-

figuration, base on page 74

Prepare the installation site with attachment holes.
The foundation surface must be clean and un-
painted.

If using a base plate: fit two guide sleeves to the
guide sleeve holes in the base plate. See

Base

plate, guide sleeve holes on page 62

Continues on next page

Product manual - IRB 5720

3HAC079195-001 Revision: A

3 Installation and commissioning

3.3.4 Orienting and securing the robot

Summary of Contents for IRB 5720


































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 5720

Reviews:

Related manuals for IRB 5720

Brands by name

Popular brands

ABB IRB 5720, Product Manual

Search results

Summary of Contents for IRB 5720

Reviews:

Related manuals for IRB 5720

Brands by name

Popular brands