ABB HT578566 Operation Manual Download

Page: 112 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

9 Taking out of operation at short notice / 9.1 Possible emergency re-
pairs

HZTL4030_EN

Revision D

May 2017

Taking out of operation at short notice

9.1

Possible emergency repairs

WARNING

Danger of fire and explosion due to lubricating oil leaks

Leaking oil may ignite on hot surfaces. This can result in serious injuries to
personnel or fatal accidents.

Cordon off danger area.

Raise the alarm and, depending on the situation, stop the engine.

Seal the oil leak.

Soak up oil and dispose of in an environmentally compatible manner.

Wear safety gloves to protect against thermal hazards.

CAUTION

Directives for taking out of operation

Serious damage to engine or property can be caused by non-compliance
with the directives for blanking the turbocharger off the engine.

Follow the directives of the enginebuilder.

If the engine has to be brought back into operation again as quickly as possible in the event
of a turbocharger defect, the following emergency repair options exist:

If present:

Installing a replacement turbocharger

→

If present:

Installing a replacement cartridge group

→

Observe the following sections in connection with the emergency repairs mentioned.

Page

Summary of Contents for HT578566



























































































































Search results

Summary of Contents for HT578566

Reviews:

Related manuals for HT578566

Brands by name

Popular brands

ABB HT578566, Operation Manual

Search results

Summary of Contents for HT578566

Reviews:

Related manuals for HT578566

Brands by name

Popular brands