ABB HT578566 Operation Manual Download

Page: 93 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

8 Dismantling and fitting / 8.5 Removing the gas outlet flange

HZTL4030_EN

Revision D

May 2017

Gas outlet flange with 6 press-off screws

CAUTION

Cracks in the gas outlet casing

Non-observance of the action steps described can lead to inadmissible
cracks on the gas outlet flange.

Observe the maximum tightening torques when pressing off.

Follow the action steps described.

Only dismantle the gas outlet flange if this is necessary for service work.

If necessary: Treat the centering seat with rust remover through the press-off threads
and the clearance holes.

Mark the casing position for assembly.

Fig. 29: Removing the gas outlet flange

Product

Press-off screws to be used

(strength 8.8) *

Tightening torque

A130

6x M6

≤ 10 Nm

A135

6x M8

≤ 20 Nm

A140

6x M10

≤ 40 Nm

Table 33: 6 press-off screws – gas outlet flange

* not included in the ABB Turbo Systems scope of delivery.

1. Evenly press off and remove the gas outlet flange (57002) with screws (01) according to

the table. If it is not possible to press off the gas outlet flange with the maximum tight-
ening torque, contact an ABB Turbo Systems Service Station.

2. If present: Remove the C-ring (57003).

Page

Summary of Contents for HT578566



























































































































Search results

Summary of Contents for HT578566

Reviews:

Related manuals for HT578566

Brands by name

Popular brands

ABB HT578566, Operation Manual

Search results

Summary of Contents for HT578566

Reviews:

Related manuals for HT578566

Brands by name

Popular brands