manualshive.com logo in svg

ABB CP420, Installation And Operation Manual

Share
Download
ABB CP420 Installation And Operation Manual Download Page 19

Operation

ABB, 1SBC159102M0201

19

7.5 Downloading an Application

Connect the RS232 port on the PC to the COM1 port on the CP420 using a 
TK401 cable. The connection can also be made according to the illustration be-
low.

Set the dip switch 

SW7 = ON

. After the self-test, the system menu will be 

displayed on the screen and the operator terminal is ready to download the 
application. 
Start CP400Soft and open the application file to be downloaded. Make sure that 
the communication parameters are correctly configured. Also remember to 
compile the file before downloading it. The file has to be compiled every time a 
change has been made in the file before downloading it. 

9-pin male

9-pin female

RXD 2

2 RD

TXD 3

3 SD

GND 5

5 SG

RTS 7

1 CD

CTS 8

4 DTR
6 DSR
7 RTS
8 CTS

Note:

COM2 is mainly used for controller communication. When used for PC communica-

tion, the pin setting described for COM2 in chapter

5 Communication Ports

 is used.

Warning:

To avoid an electrical shock, be sure to switch off the power before connecting the 

download cable to the operator terminal.

Summary of Contents for CP420


























Reviews:

No comments

Brands by name

Popular brands

Load more brands