background image

Electrical safety

This equipment complies with the requirements of CEI/IEC 
61010-1:2001-2 ‘Safety Requirements for Electrical Equipment 
for Measurement, Control and Laboratory Use’. If the 
equipment is used in a manner NOT specified by the Company, 
the protection provided by the equipment may be impaired. 

Symbols

One or more of the following symbols may appear on the 
equipment labelling:

Warning – refer to the manual for instructions

Caution – risk of electric shock

Protective earth (ground) terminal

Earth (ground) terminal

Direct current supply only

Alternating current supply only

Both direct and alternating current supply

The equipment is protected through double insulation

Information in this manual is intended only to assist our 
customers in the efficient operation of our equipment. Use of 
this manual for any other purpose is specifically prohibited and 
its contents are not to be reproduced in full or part without 
prior approval of the Technical Publications Department.

Health and safety

To ensure that our products are safe and without risk to health, 
the following points must be noted:

•  The relevant sections of these instructions must be read 

carefully before proceeding.

•  Warning labels on containers and packages must be 

observed.

•  Installation, operation, maintenance and servicing must 

only be carried out by suitably trained personnel and in 
accordance with the information given.

•  Normal safety precautions must be taken to avoid the 

possibility of an accident occurring when operating in 
conditions of high pressure and/or temperature.

•  Chemicals must be stored away from heat, protected from 

temperature extremes and powders kept dry. Normal safe 
handling procedures must be used.

•  When disposing of chemicals ensure that no two chemicals 

are mixed.

Safety advice concerning the use of the equipment described in 
this manual or any relevant hazard data sheets (where 
applicable) may be obtained from the Company address on the 
back cover, together with servicing and spares information.

Summary of Contents for C1950









Reviews: