ABB ABILITY SSC600 Operation Manual Download Page 47

Page: 47 / 70

• Check: compare the contents of the backup and current device state. Check fails

if the contents do not match, and passes if they match.

This view also shows the newly added, factory-reset devices, with IP address

192.168.2.10 (see bottom-most device in

Figure 30

). Any of the existing

backups can be deployed to this device. There can only be one factory-reset

device visible at a time, otherwise IP address conflict would occur.

Figure 30: Backup view

4.2

Disturbance identification

Disturbances and their causes can be identified by physical or WEB HMI indicator

LEDs: Ready, Start and Trip. During normal operation, the Ready LED is steady

green.

Table 10: Physical LED indications

LED

State

Description

Start LED

Green, steady

Protection started

Start LED

Green, flashing

Protection function blocked

Trip LED

Green, steady

Protection operated

Ready LED

Green, flashing

Internal fault

Alarm LED

Green, steady

Programmable LED in alarm

state

1MRS758850 D

IED operation

SSC600

Operation Manual

Summary of Contents for ABILITY SSC600






































































Search results

Summary of Contents for ABILITY SSC600

Reviews:

Related manuals for ABILITY SSC600

Brands by name

Popular brands

ABB ABILITY SSC600, Operation Manual

Search results

Summary of Contents for ABILITY SSC600

Reviews:

Related manuals for ABILITY SSC600

Brands by name

Popular brands