ABB A175-M66 Operation Manual Download

Page: 114 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.14 Removing and installing turbine-
end nozzle ring

HZTL4033_EN

Rev.H

July 2021

9.14

Removing and installing turbine-end nozzle ring

Removing the nozzle ring

If only the nozzle ring has to be removed, this can be done at the turbine end.

CAUTION

Leaking connection

Reusing the removed spiral-wound gasket (61050) will result in leaking con-
nections. Spiral-wound gaskets may only be used once.

Provide

new

spiral-wound gasket (61050).

NOTICE

Blocked areas on nozzle ring

If a nozzle ring is blocked in some areas or is covered by loose parts, it is re-
commended to appoint an ABB Turbocharging Service Station to inspect the
turbine blades and carry out a crack inspection.

In order to access the fixing screws, and loop around and transport the gas inlet casing, the
insulation has to be removed as required.

CAUTION

Damaged cleaning pipes

When looping around, ensure that any cleaning pipes present are not
pressed or damaged.

Never secure the lifting gear to the cleaning pipes.

Page

112

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operation Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands