Abatement Technologies AIRE GUARDIAN AG8000 Instruction Manual Download Page 5

 

FEATURE IDENTIFICATION 

 

 

A. 

Foam gasket. The 1" thick foam 
gasket provides a seal against the 
ceiling when the header is raised to 
the ceiling. 

B. 

Header opening markers. In order to 
help align the unit, there are arrow 
marks on the outside of the header 
that indicate where the opening inside 
the unit begins and ends. Position the 
arrow furthest away from the door to 
align with the ceiling grid. 

C. 

12" x 12" window & pass-thru. A total 
of two clear windows allow visibility 
into and out of the fabric enclosure. 
The windows are attached via hook 
and loop on three sides, enabling it to 
be opened and act as pass-throughs 
for items such as pipe or conduit. 

D. 

Handles. A total of 8 handles are 
located at the corners of the mobile 
containment cart to assist in transport. 

E. 

Fiberglass extension ladder. The 
AIRE GUARDIAN® AG8000 was 
designed around the included 
fiberglass extension ladder and should 
only be used with this ladder. 

Read all 

warning and instruction labels 
located on the ladder as well as the 
instructions within this manual to 
properly operate the ladder.

 

F. 

Door. Door opening of 54.5" H x 22" 
W.  

G. 

Casters. This unit has 4 lockable 
swivel casters. 

 

Lockable  recessed  handle.  The  lockable  door  helps 
protect  tools  and  equipment  within  the  mobile 
containment cart when not in use. 

 

Note: 

To reduce the risk being locked out of the mobile 

cart, Abatement Technologies suggests making a copy of 
the key and storing the master in a secure place. 

 

Summary of Contents for AIRE GUARDIAN AG8000





















Reviews: