Abatement Technologies AIRE GUARDIAN AG8000 Instruction Manual Download Page 16

15 

 

13. When finished with the ceiling work, replace the ceiling tile and close the top cover 

by zipping up the two zippers and engaging the hook and loop on the short edge 
near the ladder. 

14. Undo the hook and loop straps that secured the top of the ladder and then fully 

collapse the ladder. 

15. Before  exiting  the  unit,  be  sure  to  decontaminate  yourself  and  the  inside  of  the 

mobile containment cart using a HEPA filter vacuum. 

16. Completely lower top header of the unit with the raising/lowering mechanism with 

either the provided hand crank or a power drill. 

17. Unplug  the  power  supply  cord  and  wrap  the  cord  around  the  cord  wrap,  if 

necessary. 

18. Unlock all four of the casters by lifting the pedal on the casters up with your work 

shoe. 

19. Move the unit to the next desired location, being careful to avoid any contact with 

signs or devices mounted on the walls or ceiling. 

20. Repeat procedure starting from step 5, as needed. 

 

CARE OF THE UNIT 

 

  Clean with a mild water based cleaner or soap and water. Do not use hydrocarbon 

based cleaners. 

  Do not place items on the vinyl enclosure. 

  Do not subject the vinyl enclosure to sharp or abrasive objects. 

  Be sure all metal components are properly secured during transport and in storage 

so they cannot fall and cause personal injury or property damage. 

  Do not expose the vinyl enclosure to high heat. 

 

AIRE GUARDIAN® AG8000 SPECIFICATIONS 

 

FEATURE 

SPECIFICATION 

Weight with ladder 

325 lbs (147.4 kg) (air scrubber and pressure 
monitor not included) 

Maximum working ceiling 
height 

10'-2" [312 cm] 

Unit Height, Fully Collapsed 

6'-5.5" [196 cm] 

Unit Length x Width 

62" L x 32" W [157.5 cm L x 81.3 cm W] 

Header opening dimensions 

36" L x 22" W [91.4 cm L x 55.9 cm W] 

Door 

54.5" H x 22" W [138.5 cm H x 56 cm W] door 
opening; lockable handle 

Hardside wall material 

Clear polycarbonate provides visibility and allows 
light into the unit. 

Hardside wall material UL94 
flammability rating 

V0 

Fabric enclosure 

Fabric enclosure is removable and secured by hook 
and loop; includes two 12"x12" clear windows that 
each acts as a pass-through (window secured by 
hook and loop) (P/N: AG8000ENC-FR). 

Summary of Contents for AIRE GUARDIAN AG8000





















Reviews: