ABACUS IT-DR OMEGA Page 15 Manual Download | Manualshive

Page: 15 / 19

background image

Exhaust gas extraction and appliance settings have to be performed after a permanent
operation of 10 minutes minimum.

Important:

Please, copy the serial numbers located on the nameplate (burner box) in the
Installation record (last page), then send us the completed Installation record.
Warranty claims can only be enforced if the Installation record was sent to us.

If you have any questions in connection with installation, please call

our hotline:

+49/9132/7416-11

15

«
...
13
14
15
16
17
...
»

Summary of Contents for IT-DR OMEGA




















Reviews:

No comments

Related manuals for IT-DR OMEGA

Brand: Daewoo Pages: 9

Brand: Vaillant Pages: 40

Leslie F-1240LDW

Brand: Circor Pages: 19

Brand: NEO TOOLS Pages: 43

Brand: A.O. Smith Pages: 4

Brand: Swim & Fun Pages: 136

Brand: Dyna-Glo Pages: 41

MiniTank WM-2.5

Brand: Waiwela Pages: 20

Brand: VOLTOMAT HEATING Pages: 170

Brand: Trane Pages: 8

Brand: Melchioni Pages: 44

Brand: Truma Pages: 36

Brand: DeLonghi Pages: 5

Brand: Macon Pages: 24

Brand: Bryant Pages: 10

EzFit EZ 100-76

Brand: BOCK Pages: 11

Brand: Thermomart Pages: 3

Brand: DR. Heater Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands