background image

6 VMICPCI-7055/CPCI-7055RC Hardware Reference Manual 

Publication No. 500-657055-000 Rev. G

Compliance Information

This chapter provides the applicable information regarding regulatory 
compliance for the VMICPCI-7055/CPCI-7055RC.

Abaco’s VMICPCI-7055/CPCI-7055RC has been evaluated to and has met the 
requirements for compliance to the following standards:

International Compliance

• EN55022:1998/CISPR 22:1997

• IEC61000-4-2

• IEC61000-4-3

• IEC61000-4-4

• IEC61000-4-5

• IEC61000-4-6

European Union (CE Mark)

• BS EN55024 (1998 w A1:01 & A2: 03)

• BS EN55022 (Class A)

United States

• FCC Part 15, Subpart B, Section 109, Class A

Australia/New Zealand

• AS/NZS CISPR 22 (2002) Class A

Canada

• ICES-003 Class A

FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC Class A

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a commercial environment. This equipment 

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with 

the instruction manual, may cause harmful interference to radio communications. Operation of this 

equipment in a residential area is likely to cause harmful interference in which case the user will be 

required to correct the interference at his own expense.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void 

Summary of Contents for VMICPCI-7055








































































Reviews: