AB Inflatables ABJET Owner'S Manual Download

Page: 40 / 46

ENGINE MAINTENANCE / ENGINE BREAK-IN INSPECTION / GENERAL ENGINE MAINTENANCE SCHEDULE

WARNING

Failure to properly maintain the boat according to the maintenance

schedule can make it unsafe to operate.

Engine Break-in Inspection

We suggest during the first ten hours of use do not full

throttle the engine. A 3⁄4 throttle is recommended while the

engine makes a good break-in.

ALWAYS refer to the BRP Operators Manual included in the

Owner’s package for further and specific details.

General Engine Maintenance Schedule

ALWAYS CHECK THE LATEST VERSION OF THE BRP OPERA-

TORS MANUAL INCLUDED IN THE OWNER’S PACKAGE TO

KNOW WHEN THE ENGINE NEEDS TO BE STRICTLY SERVICED

IN ORDER TO KEEP A GOOD PERFORMANCE AND EXTEND ITS

LIFETIME. In case of questions consult your preferred ABJET

dealer.

MAINTENANCE & INSPEC TIONS

The maintenance schedule does not exempt the pre-ride

inspection (Refer to Use and Performance chapter).

Summary of Contents for ABJET















































Search results

Summary of Contents for ABJET

Reviews:

Related manuals for ABJET

Brands by name

Popular brands

AB Inflatables ABJET, Owner'S Manual

Search results

Summary of Contents for ABJET

Reviews:

Related manuals for ABJET

Brands by name

Popular brands