background image

 

Operators and Maintenance Manual 

 

Display

 

EEM MOT 01 FE01.05

 

Page 

14/16

 

 

Copyright: 

Auto & Aero Technologies Sp. z o.o. 

Mazowiecka 10/5, 20-723 Lublin, Poland  

 email: [email protected] 

  

www.aatech.pl 

 

 

by  means  of  service  software  provided  by  the  Manufacturer  and  the 
dedicated diagnostic interface. 

5.7.  Spare parts 

The instrument does not contain any user-serviceable parts. The user is not 
allowed to disassemble it nor replace any subassemblies.  

 

6.  Warranty 

1.

 

Auto & Aero Technologies Sp. z  o.o.  warrants this product to be free 
from defects in materials and workmanship.  

2.

 

Auto & Aero Technologies Sp. z o.o. warrants proper operation of the 
product  if  it  is  used  in  accordance  with  its  intended  purpose  and  in 
accordance with the Operators and Maintenance Manual.  

3.

 

Auto  &  Aero  Technologies  Sp.  z  o.o.  warrants  this  product  for  12 
months from date of purchase. 

4.

 

Auto  &  Aero  Technologies  Sp.  z  o.o.  will,  at  its  sole  option,  repair  or 
replace  any  components  that  fail  in  normal  use.  Such  repairs  or 
replacement  will  be  made  at  no  charge  to  the  customer  for  parts  or 
labour.  The  customer  is,  however,  responsible  for  any  transportation 
cost. The repair or replacement will be completed within 30 days from 
delivery  of  the  product  to  Auto  &  Aero  Technologies  Sp.  z  o.o. 
However,  if  the  failure  is  possible  to  be  eliminated  by  means  of 
updating 

the product’s firmware, 

and if Auto & Aero Technologies Sp. 

z  o.o.  provides  the  customer  with  appropriate  service  tools,  the 
Customer will conduct firmware update by themselves. 

5.

 

Any  warranty  repair  will  extend  the  warranty  for  the  time  of  the 
repair. 

6.

 

If a valid warranty claim is lodged within months 7 to 12 after date of 
purchase,  the  warranty  extends  for  a  further  6  months  after 
completion of the warranty repair.  

7.

 

This warranty does not cover failures due to:  

Summary of Contents for EEM FE01.01

















Reviews: