background image

General warranty conditions A2B ACCORRONI E.G.

• anomalies or faulty operation of the power supply, hydraulic,

gas, chimneys or flues (if required by the Product) *;

• damage and damage caused by carelessness, negligence, tampering, 

failure regular maintenance (cleaning of air filters, cleaning of 

evaporating batteries, cleaning

condensing coils, condensate drain hole cleaning, terminal clamping

electrical systems, disassembly, inability to use, repairs carried out by 

personnel unauthorized *, and all the provisions of the Product use 

manual;

• Products that present internal and external pipe blockages also

track, of the cooling circuit due to lack of cleaning and / or to

failure to properly carry out the vacuum operation at the plant;

• rubber seals and rubber components, such as consumables

oil, filters, refrigerants, plastic parts, mobile or removable *;

• breakage or malfunction of the remote control.

• the Products where the use of non-original and / or inadequate spare 

parts is detected;

• the Products on which the first start-up (if required) or the

maintenance by personnel other than qualified person;

• Products not started within 3 months of the shipment document for 

exit from the A2B facilities

ACCORRONI E.G .. In this case it is up to the buyer to prove that

what was found is covered by the guarantee;

• damage caused by failure to adopt the ordinary precautions for

keep the Product in good condition: avoiding overheating,

corrosion, scale, breakage caused by stray current, condensation,

aggressiveness or acidity of water, improper descaling treatments, lack

of water, sludge or limestone deposits, lack of electrical power

or gas *;

• damage caused by positioning the Product in damp, dusty 

environments or in any case unsuitable for its correct operation;

• damage caused by storage of the Product in environments unsuitable 

for it correct storage before installation;

• damage caused by the inefficiency / inadequacy of structures or 

systems (electric, hydraulic *) connected to the Product;

• damage caused by incorrect sizing of the Product based on its use;

• damage caused by malicious acts, force majeure (weather events, fire,

lightning, electrical interference, oxidation, rust, earthquakes, theft) * 

and / or cases fortuitous;

• damage caused by failure to contain air pollution and

acoustic except for the regulatory limits in place;

• Everything listed in this point determines that the intervention is

completely at the expense of the Buyer / Consumer who will have to pay

the costs for home delivery, verification occurred at the assistance 

center and transport, the material used, the labor *, whether the supply 

occurred directly through A2B ACCORRONI E.G. or through another

subject who markets the Product;

* These lists of situations are by way of example but not exhaustive

3) TYPES, METHODS AND INTERVENTION TIMES

• In order to report the alleged lack of conformity of the Product, such as

necessary condition for the activation of the guarantee, the Buyer /

Product consumer, through the retailer, that is the person with whom

has finalized the Product purchase contract, will have to contact the 

office post-sale of A2B ACCORRONI E.G.

• At the time of reporting, identification data and records must be 

provided

End User contacts, in addition to the identification code of the Product 

in question

(model and registration number). These indications will be necessary to 

allow A2B ACCORRONI E.G. to verify the release date of the same 

Product from the warehouses, in the absence of the identification code, 

the guarantee does not can be applied.

• Should the service center be found during this inspection

a lack of conformity of the Product with the same service center will be 

activated to carry out the necessary repair. A2B ACCORRONI E.G. reserve 

of

decide whether to replace the Product or part of it in the case in

which, at its sole discretion, is not economically repaired

cheap. Repair or replacement will not incur additional costs

for the End User or for the reseller from which the End User has

purchased the same Product. In this case also the aforementioned 

expenses inspection will not be charged.

• The Buyer / Consumer must report the malfunction and / or 

defectiveness

in the current warranty period and in any case no later than two months 

from discovery of the defect or failure.

• any interventions, repairs or replacements of the Product will not give

however, it may result in extensions or renewals of the warranty or 

modification

of its original expiry. The parts replaced under warranty will remain of

property of A2B ACCORRONI E.G ..

• in the replacement of part of the Product or of the complete Product 

will be able to be used parts or Products identical or with the same 

characteristics.

The previously described assistance procedures may

be subject to changes and / or updates by A2B
Please note that not everything described above is never extends to the 

obligation of compensation for damages and reimbursement of 

expenses or costs any nature suffered by people or things, and that 

nobody, except that A2B ACCORRONI E.G., is authorized to modify the 

terms above or release others both verbal and written. For any dispute, 

the competent court is the Court of Ancona.3

By "Product" from here on out and for the entire document, we mean 

and we must refer exclusively to the A2B ACCORRONI E.G .. brand 

product By "Buyer" from now on and for the entire document, we mean 

and reference must be made to the natural or legal person who has 

purchased the Product, regardless of whether the seller is A2B 

ACCORRONI E.G. or other person marketing branded products A2B 

ACCORRONI E.G ..

• This warranty for A2B branded products ACCORRONI E.G.

it is subject to the community legislation in force 99/44 / EC, to the 

legislation national DL 24/02 and DL 206/2005 applicable to consumer 

goods;

• This warranty is issued on the Products in question and is valid for

twenty-four (24) months starting from the date of purchase of the 

Product (date tax document issued at the time of purchase) to which it 

refers if the buyer purchases it for purposes unrelated to his business, 

commercial and professional ("The Consumer"). On the contrary, the 

present warranty will have twelve (12) months duration from the date of 

purchase of the Product (date

tax document issued at the time of purchase) if the Product to which

refers to is purchased for purposes related to its business,

commercial and professional. The warranty terms above are valid a

provided that the Products are put into operation within 3 months from 

the date of leaving the A2B ACCORRONI E.G. facilities;

• For the Products for which the first ignition is required,

under penalty of forfeiture of the guarantee, this will start from the start-

up of the same Products to be demonstrated by appropriate 

documentation and provided that this take place within 6 months of 

A2B ACCORRONI E.G. of the same product. Products for which the first 

ignition is foreseen mandatory are those belonging to the Renewable 

Energy category, Air conditioning in the commercial catalog or in the 

price list;

• the Purchaser of the Product must contact the retailer, that is the 

person with the

which has finalized the Product purchase contract, for any request

concerning the guarantee on the same.

1) EFFECTIVENESS AND OPERATION

• This warranty is operational and effective provided they are

 

observed

instructions and warnings for correct installation, operation, use and

maintenance that accompanies the Product and in compliance with the 

laws in force. With reference to this, the Product must be installed by 

skilful technicians and by qualified personnel in compliance with laws 

and regulations in force (UNI-EN, UNICIG, VV.FF,

IEC .... *). It must also be mounted only on systems manufactured by

personnel with PEF / F-Gas (European F-Gas Patent) as per DPR

43/2012. It should be noted, however, that the installer remains solely 

responsible installation.

• The Product Buyer must keep and show the tax document

issued at the time of purchase to be able to take advantage of the 

warranty with the durations described above, otherwise the date of the 

delivery note.

• The guarantee and the interventions that will take place within the 

described periods above in accordance with the previously mentioned 

regulations, including the first one goodwill for the Products that 

require it, will be covered exclusively the product itself will not extend to 

the plant and cannot be assimilated in any way to tests and / or checks 

of the same that are reserved by law to installers and authorized 

maintenance technicians and in any case under load and under the

responsibility of the Purchaser of the Product and of the same. No 

intervention, from start-up to warranty and out of warranty intervention, 

relieves the owner of the plant from the respect and the necessary 

verifications

 

according to norms or yes replaces the same. The latter 

also, at his own expense, is responsible for guarantee safe operating 

conditions for each intervention as per Legislative Decree 81/08, as well 

as compliance with routine maintenance by carry out as per the manual 

attached to the Product.

2) EXCLUSIONS

Products or cases relating to them are excluded from this warranty

which also have only one of the following features:

• lack of refrigerant gas and therefore need to be recharged;

• Products with registration number or unit and / or documentation label

accompanying illegible, missing or altered;

• Products that have not complied with the instructions in part

installation, operation, use and maintenance contained in the manual

accompanying product;

• the Products installed without the presence of adequate electrical 

protection and the connection to earth ground;

• Products installed by unqualified personnel as required by the

current regulations, connected to electrical systems

 

/ plumbers / gas 

without the documentation required by law

(compliance, plant certification, booklet ... *);

• Products that report an increase in damage resulting from further use

of the same by the purchaser once the malfunction has occurred

and / or in an attempt to remedy the initial findings;

• interventions to be carried out with ladder, scaffolding, rolling 

scaffolding, systems of

 

elevation or lifting and / or transport; the costs 

for interventions that

 

require security measures not already present in 

the installation configuration *.

These costs remain the responsibility of the Buyer: please note that the 

assistance centers

 

are authorized to intervene only in cases where the 

Products are installed

 

at a height not exceeding 2 meters from a stable 

work plan on which one can

 

operate in accordance with Legislative 

Decree 81/08.

 

In all other cases it will be care and responsibility

of the Buyer / Consumer arrange the necessary equipment and support 

the costs for securing the technicians during the intervention;

• any transport failures (scratches, dents and the like *);

• damage due to wear, deterioration, lack of use, incorrect installation, 

breakage accidental, sudden voltage changes *;

Summary of Contents for ACCORRONI HUB RADIATOR DHP 3.0 + 3.0

















































Reviews: